UK Global Tariff
UK Global Tariff, chapter 72: Iron and steel
- 593Tariff lines
- 0%–50%Rate
Chapter 72 has 593 lines in the UK Global Tariff, spread over 29 headings.
Rates run from 0% to 50%, averaging 23.8%; 311 lines are duty-free.
The most detailed heading is 7219 (flat-rolled products of stainless steel, of a width of 600 mm or more) with 57 lines.
The most common rate is zero, on 311 lines.
The highest is 50% on 7208 10 00 00 (in coils, not further worked than hot-rolled, with patterns in relief).
7201 Pig iron and spiegeleisen in pigs, blocks or other primary forms
- 7201 10 11 10Pig iron ingots with a length of not more than 350 mm, a width of not more than 150 mm, a height of not more than 150 mm
- 7201 10 11 90Containing by weight 1% or less of silicon: other
- 7201 10 19 00Containing by weight more than 1% of silicon
- 7201 10 30 10Pig iron ingots with a length of not more than 350 mm, a width of not more than 150 mm, a height of not more than 150 mm, containing by weight not more than 1% of silicon
- 7201 10 30 90Containing by weight not less than 0.1% but less than 0.4%: other
- 7201 10 90 00Containing by weight less than 0.1% of manganese
- 7201 20 00 00Non-alloy pig iron containing by weight more than 0.5% of phosphorus
- 7201 50 10 00Alloy pig iron containing by weight not less than 0.3% but not more than 1% of titanium and not less than 0.5% but not more than 1% of vanadium
- 7201 50 90 00Alloy pig iron; spiegeleisen: other
7202 Ferro-alloys
- 7202 11 20 00With a granulometry not exceeding 5 mm and a manganese content by weight exceeding 65%
- 7202 11 80 00Containing by weight more than 2% of carbon: other
- 7202 19 00 00Ferro-alloys, ferro-manganese, other
- 7202 21 00 00Containing by weight more than 55% of silicon
- 7202 29 10 00Containing by weight 4% or more but not more than 10% of magnesium
- 7202 29 90 00Ferro-alloys, ferro-silicon, other, other
- 7202 30 00 00Ferro-alloys, ferro-silico-manganese
- 7202 41 10 00Containing by weight more than 4% but not more than 6% of carbon
- 7202 41 90 00Containing by weight more than 6% of carbon
- 7202 49 10 20Containing by weight more than 30% but not more than 90% of chromium (super-refined ferrochromium)
- 7202 49 10 90Containing by weight not more than 0.05% of carbon: other
- 7202 49 50 11Containing by weight not more than 0.1% of carbon and more than 30% but not more than 90% of chromium (super-refined ferrochromium)
- 7202 49 50 19With a chromium content by weight of 30% and more: other
- 7202 49 50 90Containing by weight more than 0.05% but not more than 0.5%: other
- 7202 49 90 00Containing by weight more than 0.5% but not more than 4% of carbon
- 7202 50 00 00Ferro-alloys, ferro-silico-chromium
- 7202 60 00 00Ferro-alloys, ferro-nickel
- 7202 70 00 00Ferro-alloys, ferro-molybdenum
- 7202 80 00 00Ferro-alloys, ferro-tungsten and ferro-silico-tungsten
- 7202 91 00 00Ferro-alloys, other, ferro-titanium and ferro-silico-titanium
- 7202 92 00 00Ferro-alloys, other, ferro-vanadium
- 7202 93 00 00Ferro-alloys, other, ferro-niobium
- 7202 99 10 00Ferro-alloys, other, other, ferro-phosphorus
- 7202 99 30 00Ferro-alloys, other, other, ferro-silico-magnesium
- 7202 99 80 30Calcium-silicon - an alloy that contains by weight 16% or more of calcium, 45% or more of silicon, not less than 4% but less than 14% of iron and not more than 10% of any other element; whether or not presented in bulk, packaged in bags or in steel drums, enclosed in steel sheets (or cored wire), or otherwise presented
- 7202 99 80 90Ferro-alloys, other, other, other, other
7203 Ferrous products obtained by direct reduction of iron ore and other spongy ferrous products, in lumps, pellets or similar forms; iron having a minimum purity by weight of 99,94 %, in lumps, pellets or similar forms
7204 Ferrous waste and scrap; remelting scrap ingots of iron or steel
- 7204 10 00 00Waste and scrap of cast iron
- 7204 21 10 10Containing by weight 8% or more of nickel: scrap
- 7204 21 10 90Containing by weight 8% or more of nickel: other
- 7204 21 90 10Waste and scrap of alloy steel: of stainless steel, other, scrap
- 7204 21 90 90Waste and scrap of alloy steel: of stainless steel, other, other
- 7204 29 00 10Waste and scrap of alloy steel: other, scrap
- 7204 29 00 90Waste and scrap of alloy steel: other, other
- 7204 30 00 10Waste and scrap of tinned iron or steel: scrap
- 7204 30 00 90Waste and scrap of tinned iron or steel: other
- 7204 41 10 10Turnings, shavings, chips, milling waste, sawdust: scrap
- 7204 41 10 90Turnings, shavings, chips, milling waste, sawdust: other
- 7204 41 91 10Turnings, shavings, chips, milling waste, sawdust, filings: trimmings and stampings, in bundles, scrap
- 7204 41 91 90Turnings, shavings, chips, milling waste, sawdust, filings: trimmings and stampings, in bundles, other
- 7204 41 99 10Turnings, shavings, chips, milling waste, sawdust, filings: trimmings and stampings, other, scrap
- 7204 41 99 90Turnings, shavings, chips, milling waste, sawdust, filings: trimmings and stampings, other, other
- 7204 49 10 10Other waste and scrap: other, fragmentised (shredded), scrap
- 7204 49 10 90Other waste and scrap: other, fragmentised (shredded), other
- 7204 49 30 10Other waste and scrap: other, other, in bundles, scrap
- 7204 49 30 90Other waste and scrap: other, other, in bundles, other
- 7204 49 90 10Other waste and scrap: other, other, other, scrap
- 7204 49 90 90Other waste and scrap: other, other, other, other
- 7204 50 00 00Ferrous waste and scrap: remelting scrap ingots
7205 Granules and powders, of pig iron, spiegeleisen, iron or steel
7206 Iron and non-alloy steel in ingots or other primary forms (excluding iron of heading 7203)
7207 Semi-finished products of iron or non-alloy steel
- 7207 11 11 00Rolled or obtained by continuous casting: of free-cutting steel
- 7207 11 14 00Of a thickness not exceeding 130 mm
- 7207 11 16 00Of a thickness exceeding 130 mm
- 7207 11 90 00Of rectangular: forged
- 7207 12 10 00Rolled or obtained by continuous casting
- 7207 12 90 00Other, of rectangular (other than square) cross-section: forged
- 7207 19 12 00Rolled or obtained by continuous casting
- 7207 19 19 00Of circular or polygonal cross-section: forged
- 7207 19 80 10Blanks for angles, shapes and sections, rolled or obtained by continuous casting
- 7207 19 80 90Containing by weight less than 0.25% of carbon: other, other, other
- 7207 20 11 00Rolled or obtained by continuous casting: of free-cutting steel
- 7207 20 15 000.25% or more but less than 0.6% of carbon
- 7207 20 17 000.6% or more of carbon
- 7207 20 19 00Of rectangular: forged
- 7207 20 32 00Rolled or obtained by continuous casting
- 7207 20 39 00Other, of rectangular (other than square) cross-section: forged
- 7207 20 52 00Rolled or obtained by continuous casting
- 7207 20 59 00Of circular or polygonal cross-section: forged
- 7207 20 80 10Blanks for angles, shapes and sections, rolled or obtained by continuous casting
- 7207 20 80 90Containing by weight 0.25% or more of carbon: other, other
7208 Flat-rolled products of iron or non-alloy steel, of a width of 600 mm or more, hot-rolled, not clad, plated or coated
- 7208 10 00 00In coils, not further worked than hot-rolled, with patterns in relief
- 7208 25 00 00Of a thickness of 4.75 mm or more
- 7208 26 00 00Of a thickness of 3 mm or more but less than 4.75 mm
- 7208 27 00 00Of a thickness of less than 3 mm
- 7208 36 00 00Of a thickness exceeding 10 mm
- 7208 37 00 10Of a thickness of 4.75 mm or more but not exceeding 10 mm: intended for re-rolling
- 7208 37 00 90Of a thickness of 4.75 mm or more but not exceeding 10 mm: other
- 7208 38 00 10Of a thickness of 3 mm or more but less than 4.75 mm: intended for re-rolling
- 7208 38 00 90Of a thickness of 3 mm or more but less than 4.75 mm: other
- 7208 39 00 10Of a thickness of less than 3 mm: intended for re-rolling
- 7208 39 00 90Of a thickness of less than 3 mm: other
- 7208 40 00 10Of a thickness of 2 mm or more
- 7208 40 00 90Of a thickness of less than 2 mm
- 7208 51 20 10Of non-alloy steel, excluding tool steel
- 7208 51 20 90Of a thickness exceeding 15 mm: other
- 7208 51 91 10Of non-alloy steel, excluding tool steel
- 7208 51 91 902 050 mm or more: other
- 7208 51 98 10Of non-alloy steel, excluding tool steel
- 7208 51 98 90Less than 2 050 mm: other
- 7208 52 10 00Rolled on four faces or in a closed box pass, of a width not exceeding 1 250 mm
- 7208 52 91 10Of non-alloy steel, excluding tool steel
- 7208 52 91 902 050 mm or more: other
- 7208 52 99 00Less than 2 050 mm
- 7208 53 10 00Rolled on four faces or in a closed box pass, of a width not exceeding 1 250 mm and of a thickness of 4 mm or more
- 7208 53 90 00Of a thickness of 3 mm or more but less than 4.75 mm: other
- 7208 54 00 00Of a thickness of less than 3 mm
- 7208 90 20 10Of non-alloy steel, excluding tool steel, of a thickness exceeding 10 mm or of a thickness of 4.75 mm or more but not exceeding 10 mm and of a width of 2 050 mm or more
- 7208 90 20 90Flat-rolled products of iron or non-alloy steel, of a width: other, perforated, other
- 7208 90 80 10Not further worked than surface-treated or simply cut into shapes other than rectangular (including square)
- 7208 90 80 20Of non-alloy steel, excluding tool steel, of a thickness exceeding 10 mm or of a thickness of 4.75 mm or more but not exceeding 10 mm and of a width of 2 050 mm or more
- 7208 90 80 90Flat-rolled products of iron or non-alloy steel, of a width: other, other, other
7209 Flat-rolled products of iron or non-alloy steel, of a width of 600 mm or more, cold-rolled (cold-reduced), not clad, plated or coated
- 7209 15 00 10Of a thickness of 3 mm or more: 'electrical'
- 7209 15 00 90Of a thickness of 3 mm or more: other
- 7209 16 10 00Of a thickness exceeding 1 mm but less than 3 mm: 'electrical'
- 7209 16 90 00Of a thickness exceeding 1 mm but less than 3 mm: other
- 7209 17 10 00Of a thickness of 0.5 mm or more but not exceeding 1 mm: 'electrical'
- 7209 17 90 00Of a thickness of 0.5 mm or more but not exceeding 1 mm: other
- 7209 18 10 00Of a thickness of less than 0.5 mm: 'electrical'
- 7209 18 91 00Of a thickness of 0.35 mm or more but less than 0.5 mm
- 7209 18 99 10Annealed (known as 'black plates')
- 7209 18 99 90Of a thickness of less than 0.35 mm: other
- 7209 25 00 10Of a thickness of 3 mm or more: 'electrical'
- 7209 25 00 90Of a thickness of 3 mm or more: other
- 7209 26 10 00Of a thickness exceeding 1 mm but less than 3 mm: 'electrical'
- 7209 26 90 00Of a thickness exceeding 1 mm but less than 3 mm: other
- 7209 27 10 00Of a thickness of 0.5 mm or more but not exceeding 1 mm: 'electrical'
- 7209 27 90 00Of a thickness of 0.5 mm or more but not exceeding 1 mm: other
- 7209 28 10 00Of a thickness of less than 0.5 mm: 'electrical'
- 7209 28 90 00Of a thickness of less than 0.5 mm: other
- 7209 90 20 00Flat-rolled products of iron or non-alloy steel, of a width: other, perforated
- 7209 90 80 10Not further worked than surface-treated or simply cut into shapes other than rectangular (including square)
- 7209 90 80 90Flat-rolled products of iron or non-alloy steel, of a width: other, other, other
7210 Flat-rolled products of iron or non-alloy steel, of a width of 600 mm or more, clad, plated or coated
- 7210 11 00 10Not further worked than surface-treated or simply cut into shapes other than rectangular (including square)
- 7210 11 00 90Of a thickness of 0.5 mm or more: other
- 7210 12 20 10Not further worked than surface-treated or simply cut into shapes other than rectangular (including square)
- 7210 12 20 90Of a thickness of less than 0.5 mm: tinplate, other
- 7210 12 80 10Not further worked than surface-treated or simply cut into shapes other than rectangular (including square)
- 7210 12 80 90Of a thickness of less than 0.5 mm: other, other
- 7210 20 00 10Not further worked than surface-treated or simply cut into shapes other than rectangular (including square)
- 7210 20 00 90Plated or coated with lead, including terne-plate: other
- 7210 30 00 10Not further worked than surface-treated or simply cut into shapes other than rectangular (including square)
- 7210 30 00 90Electrolytically plated or coated with zinc: other
- 7210 41 00 20Aluminium killed; plated or coated by hot dip galvanisation with zinc and/or with aluminium, and no other metal; chemically passivated; containing by weight: 0.015% or more but not more than 0.170% of carbon, 0.015% or more but not more than 0.100% of aluminium, not more than 0.045% of niobium, not more than 0.010% of titanium and not more than 0.010% of vanadium; presented in coils, cut-to-length sheets and narrow strips
- 7210 41 00 30Plated or coated by hot dip galvanisation, whether or not alloyed with silicon; chemically passivated; with or without any additional surface treatment such as oiling or sealing; containing by weight: not more than 0.5% of carbon, not more than 1.1% of aluminium, not more than 0.12% of niobium, not more than 0.17% of titanium and not more than 0.15% of vanadium; presented in coils, cut-to-length sheets and narrow strips
- 7210 41 00 80Not further worked than surface-treated or simply cut into: other
- 7210 41 00 90Otherwise plated or coated with zinc: corrugated, other
- 7210 49 00 20Aluminium killed; plated or coated by hot dip galvanisation with zinc and/or with aluminium, and no other metal; chemically passivated; containing by weight: 0.015% or more but not more than 0.170% of carbon, 0.015% or more but not more than 0.100% of aluminium, not more than 0.045% of niobium, not more than 0.010% of titanium and not more than 0.010% of vanadium; presented in coils, cut-to-length sheets and narrow strips
- 7210 49 00 30Plated or coated by hot dip galvanisation, whether or not alloyed with silicon; chemically passivated; with or without any additional surface treatment such as oiling or sealing; containing by weight: not more than 0.5% of carbon, not more than 1.1% of aluminium, not more than 0.12% of niobium, not more than 0.17% of titanium and not more than 0.15% of vanadium; presented in coils, cut-to-length sheets and narrow strips
- 7210 49 00 80Not further worked than surface-treated or simply cut into: other
- 7210 49 00 90Otherwise plated or coated with zinc: other, other
- 7210 50 00 10Not further worked than surface-treated or simply cut into shapes other than rectangular (including square)
- 7210 50 00 90Plated or coated with chromium oxides or with chromium: other
- 7210 61 00 20Aluminium killed; plated or coated by hot dip galvanisation with zinc and/or with aluminium, and no other metal; chemically passivated; containing by weight: 0.015% or more but not more than 0.170% of carbon, 0.015% or more but not more than 0.100% of aluminium, not more than 0.045% of niobium, not more than 0.010% of titanium and not more than 0.010% of vanadium; presented in coils, cut-to-length sheets and narrow strips
- 7210 61 00 30Plated or coated by hot dip galvanisation, whether or not alloyed with silicon; chemically passivated; with or without any additional surface treatment such as oiling or sealing; containing by weight: not more than 0.5% of carbon, not more than 1.1% of aluminium, not more than 0.12% of niobium, not more than 0.17% of titanium and not more than 0.15% of vanadium; presented in coils, cut-to-length sheets and narrow strips
- 7210 61 00 80Not further worked than surface-treated or simply cut into: other
- 7210 61 00 90Plated or coated with aluminium-zinc alloys: other
- 7210 69 00 20Aluminium killed; plated or coated by hot dip galvanisation with zinc and/or with aluminium, and no other metal; chemically passivated; containing by weight: 0.015% or more but not more than 0.170% of carbon, 0.015% or more but not more than 0.100% of aluminium, not more than 0.045% of niobium, not more than 0.010% of titanium and not more than 0.010% of vanadium; presented in coils, cut-to-length sheets and narrow strips
- 7210 69 00 30Plated or coated by hot dip galvanisation with aluminium and/or magnesium, whether or not alloyed with silicon; chemically passivated; with or without any additional surface treatment such as oiling or sealing; containing by weight: not more than 0.5% of carbon, not more than 1.1% of aluminium, not more than 0.12% of niobium, not more than 0.17% of titanium and not more than 0.15% of vanadium; presented in coils, cut-to-length sheets and narrow strips
- 7210 69 00 80Not further worked than surface-treated or simply cut into: other
- 7210 69 00 90Plated or coated with aluminium: other, other
- 7210 70 10 15Not further worked than surface-treated or simply cut into: tinplate, not painted
- 7210 70 10 19Not further worked than surface-treated or simply cut into: tinplate, other
- 7210 70 10 91Not further worked than surface-treated or simply cut into: other
- 7210 70 10 95Tinplate, varnished: other
- 7210 70 80 11Of non-alloy steel, painted, varnished or coated with plastics on at least one side, excluding products with a final coating of zinc-dust (a zinc-rich paint, containing by weight 70% or more of zinc) and excluding products with a substrate with a metallic coating of chromium or tin
- 7210 70 80 20Coated or plated with tin: not painted
- 7210 70 80 23Coated or plated with tin: other
- 7210 70 80 25Not further worked than surface-treated or simply cut into: other, other
- 7210 70 80 91Of non-alloy steel, painted, varnished or coated with plastics on at least one side, excluding so-called 'sandwich panels' of a kind used for building applications and consisting of two outer metal sheets with a stabilising core of insulation material sandwiched between them, and excluding those products with a final coating of zinc-dust (a zinc-rich paint, containing by weight 70% or more of zinc) and excluding products with a substrate with a metallic coating of chromium or tin
- 7210 70 80 92Coated or plated with tin: not painted
- 7210 70 80 93Coated or plated with tin: other
- 7210 70 80 95Painted, varnished or coated with plastics: other, other, other, other
- 7210 90 30 10Not further worked than surface-treated, including cladding, or simply cut into shapes other than rectangular (including square)
- 7210 90 30 90Flat-rolled products of iron or non-alloy steel, of a width: other, clad, other
- 7210 90 40 10Not further worked than surface-treated, including cladding, or simply cut into shapes other than rectangular (including square)
- 7210 90 40 90Flat-rolled products of iron or non-alloy steel, of a width: other, tinned and printed, other
- 7210 90 80 20Coated or plated with tin, whether or not coated with: not painted
- 7210 90 80 29Coated or plated with tin, whether or not coated with: other
- 7210 90 80 91Not further worked than surface-treated, including cladding, or simply cut into shapes other than rectangular (including square)
- 7210 90 80 92Plated or coated by hot dip galvanisation with magnesium or magnesium-zinc alloys, whether or not alloyed with silicon; chemically passivated; with or without any additional surface treatment such as oiling or sealing; containing by weight: not more than 0.5% of carbon, not more than 1.1% of aluminium, not more than 0.12% of niobium, not more than 0.17% of titanium and not more than 0.15% of vanadium; presented in coils, cut-to-length sheets and narrow strips
- 7210 90 80 99Flat-rolled products of iron or non-alloy steel, of a width: other, other, other, other
7211 Flat-rolled products of iron or non-alloy steel, of a width of less than 600 mm, not clad, plated or coated
- 7211 13 00 11Of a width not exceeding 350 mm and of a thickness of 50 mm or more
- 7211 13 00 19Rolled on four faces or in a closed box pass, of a width: other
- 7211 14 00 10Of a width exceeding 500 mm
- 7211 14 00 91Of a width not exceeding 350 mm and of a thickness of 50 mm or more
- 7211 14 00 95Of a width not exceeding 500 mm: other
- 7211 19 00 10Of a width exceeding 500 mm
- 7211 19 00 91Of a width not exceeding 350 mm and of a thickness of 50 mm or more
- 7211 19 00 95Of a width not exceeding 500 mm: other
- 7211 23 20 10Of a width exceeding 500 mm
- 7211 23 20 90Of a width not exceeding 500 mm
- 7211 23 30 10Of a width exceeding 500 mm
- 7211 23 30 91In coils intended for the manufacture of tinplate
- 7211 23 30 99Of a width not exceeding 500 mm: other
- 7211 23 80 11In coils, annealed (known as 'black plates')
- 7211 23 80 19Of a width exceeding 500 mm: other
- 7211 23 80 93Annealed (known as 'black plates')
- 7211 23 80 95In coils intended for the manufacture of tinplate: other
- 7211 23 80 97In coils, annealed (known as 'black plates')
- 7211 23 80 99Of a width not exceeding 500 mm: other, other
- 7211 29 00 11Of a width exceeding 500 mm: 'electrical'
- 7211 29 00 19Of a width exceeding 500 mm: other
- 7211 29 00 91Of a width not exceeding 500 mm: 'electrical'
- 7211 29 00 99Of a width not exceeding 500 mm: other
- 7211 90 20 00Flat-rolled products of iron or non-alloy steel, of a width: other, perforated
- 7211 90 80 10Not further worked than surface-treated
- 7211 90 80 20Of a width exceeding 500 mm: other
- 7211 90 80 90Of a width not exceeding 500 mm
7212 Flat-rolled products of iron or non-alloy steel, of a width of less than 600 mm, clad, plated or coated
- 7212 10 10 00Tinplate, not further worked than surface-treated
- 7212 10 90 11Not further worked than surface-treated
- 7212 10 90 19Of a width exceeding 500 mm: other
- 7212 10 90 90Of a width not exceeding 500 mm
- 7212 20 00 11Not further worked than surface-treated
- 7212 20 00 19Of a width exceeding 500 mm: other
- 7212 20 00 90Of a width not exceeding 500 mm
- 7212 30 00 20Aluminium killed; plated or coated by hot dip galvanisation with zinc and/or with aluminium, and no other metal; chemically passivated; containing by weight: 0.015% or more but not more than 0.170% of carbon, 0.015% or more but not more than 0.100% of aluminium, not more than 0.045% of niobium, not more than 0.010% of titanium and not more than 0.010% of vanadium; presented in coils, cut-to-length sheets and narrow strips
- 7212 30 00 30Plated or coated by hot dip galvanisation, whether or not alloyed with silicon; chemically passivated; with or without any additional surface treatment such as oiling or sealing; containing by weight: not more than 0.5% of carbon, not more than 1.1% of aluminium, not more than 0.12% of niobium, not more than 0.17% of titanium and not more than 0.15% of vanadium; presented in coils, cut-to-length sheets and narrow strips
- 7212 30 00 80Not further worked than surface-treated: other
- 7212 30 00 90Otherwise plated or coated with zinc: other
- 7212 40 20 10Tinplate, not further worked than varnished: not painted
- 7212 40 20 19Tinplate, not further worked than varnished: other
- 7212 40 20 91Not further worked than surface-treated
- 7212 40 20 93Of a width exceeding 500 mm: other
- 7212 40 20 99Of a width not exceeding 500 mm
- 7212 40 80 01Of non-alloy steel, painted, varnished or coated with plastics on at least one side, excluding products with a final coating of zinc-dust (a zinc-rich paint, containing by weight 70% or more of zinc) and excluding products with a substrate with a metallic coating of chromium or tin
- 7212 40 80 12Coated or plated with tin: not painted
- 7212 40 80 14Coated or plated with tin: other
- 7212 40 80 15Not further worked than surface-treated: other, other
- 7212 40 80 21Of non-alloy steel, painted, varnished or coated with plastics on at least one side, excluding so-called 'sandwich panels' of a kind used for building applications and consisting of two outer metal sheets with a stabilising core of insulation material sandwiched between them, and excluding those products with a final coating of zinc-dust (a zinc-rich paint, containing by weight 70% or more of zinc) and excluding products with a substrate with a metallic coating of chromium or tin
- 7212 40 80 30Coated or plated with tin: not painted
- 7212 40 80 33Coated or plated with tin: other
- 7212 40 80 35Of a width exceeding 500 mm: other, other, other
- 7212 40 80 80Coated or plated with tin: not painted
- 7212 40 80 81Coated or plated with tin: other
- 7212 40 80 82Of non-alloy steel, painted, varnished or coated with: other
- 7212 40 80 85Coated or plated with tin: not painted
- 7212 40 80 86Coated or plated with tin: other
- 7212 40 80 87Of a width not exceeding 500 mm: other, other
- 7212 50 20 11Not further worked than surface-treated
- 7212 50 20 19Of a width exceeding 500 mm: other
- 7212 50 20 90Of a width not exceeding 500 mm
- 7212 50 30 11Not further worked than surface-treated
- 7212 50 30 19Of a width exceeding 500 mm: other
- 7212 50 30 90Of a width not exceeding 500 mm
- 7212 50 40 11Not further worked than surface-treated
- 7212 50 40 19Of a width exceeding 500 mm: other
- 7212 50 40 90Of a width not exceeding 500 mm
- 7212 50 61 20Aluminium killed; plated or coated by hot dip galvanisation with zinc and/or with aluminium, and no other metal; chemically passivated; containing by weight: 0.015% or more but not more than 0.170% of carbon, 0.015% or more but not more than 0.100% of aluminium, not more than 0.045% of niobium, not more than 0.010% of titanium and not more than 0.010% of vanadium; presented in coils, cut-to-length sheets and narrow strips
- 7212 50 61 30Plated or coated by hot dip galvanisation, whether or not alloyed with silicon; chemically passivated; with or without any additional surface treatment such as oiling or sealing; containing by weight: not more than 0.5% of carbon, not more than 1.1% of aluminium, not more than 0.12% of niobium, not more than 0.17% of titanium and not more than 0.15% of vanadium; presented in coils, cut-to-length sheets and narrow strips
- 7212 50 61 80Plated or coated with aluminium-zinc alloys: other
- 7212 50 69 20Aluminium killed; plated or coated by hot dip galvanisation with zinc and/or with aluminium, and no other metal; chemically passivated; containing by weight: 0.015% or more but not more than 0.170% of carbon, 0.015% or more but not more than 0.100% of aluminium, not more than 0.045% of niobium, not more than 0.010% of titanium and not more than 0.010% of vanadium; presented in coils, cut-to-length sheets and narrow strips
- 7212 50 69 30Plated or coated by hot dip galvanisation, whether or not alloyed with silicon; chemically passivated; with or without any additional surface treatment such as oiling or sealing; containing by weight: not more than 0.5% of carbon, not more than 1.1% of aluminium, not more than 0.12% of niobium, not more than 0.17% of titanium and not more than 0.15% of vanadium; presented in coils, cut-to-length sheets and narrow strips
- 7212 50 69 80Plated or coated with aluminium: other, other
- 7212 50 90 11Silvered, gilded, platinum-plated or enamelled
- 7212 50 90 13Not further worked than surface-treated
- 7212 50 90 14Plated or coated by hot dip galvanisation with magnesium or magnesium-zinc alloys, whether or not alloyed with silicon; chemically passivated; with or without any additional surface treatment such as oiling or sealing; containing by weight: not more than 0.5% of carbon, not more than 1.1% of aluminium, not more than 0.12% of niobium, not more than 0.17% of titanium and not more than 0.15% of vanadium; presented in coils, cut-to-length sheets and narrow strips
- 7212 50 90 19Of a width exceeding 500 mm: other, other
- 7212 50 90 92Plated or coated by hot dip galvanisation with magnesium or magnesium-zinc alloys, whether or not alloyed with silicon; chemically passivated; with or without any additional surface treatment such as oiling or sealing; containing by weight: not more than 0.5% of carbon, not more than 1.1% of aluminium, not more than 0.12% of niobium, not more than 0.17% of titanium and not more than 0.15% of vanadium; presented in coils, cut-to-length sheets and narrow strips
- 7212 50 90 95Of a width not exceeding 500 mm: other
- 7212 60 00 12Hot-rolled, not further worked than clad
- 7212 60 00 19Not further worked than surface-treated: other
- 7212 60 00 20Of a width not exceeding 500 mm: other
- 7212 60 00 50Not further worked than surface-treated
- 7212 60 00 98Flat-rolled products of iron or non-alloy steel, of a width: clad, other, other
7213 Bars and rods, hot-rolled, in irregularly wound coils, of iron or non-alloy steel
- 7213 10 00 00Containing indentations, ribs, grooves or other deformations produced during the rolling process
- 7213 20 00 00Other, of free-cutting steel
- 7213 91 10 00Of a type used for concrete reinforcement
- 7213 91 20 00Of a type used for tyre cord
- 7213 91 41 00Containing by weight 0.06% or less of carbon
- 7213 91 49 00Containing by weight more than 0.06% but less than 0.25% of carbon
- 7213 91 70 00Containing by weight 0.25% or more but not more than 0.75% of carbon
- 7213 91 90 00Containing by weight more than 0.75% of carbon
- 7213 99 10 00Containing by weight less than 0.25% of carbon
- 7213 99 90 00Containing by weight 0.25% or more of carbon
7214 Other bars and rods of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but including those twisted after rolling
- 7214 10 00 10Concrete reinforcement bars and rods, containing indentations, ribs, grooves or other deformations produced during the rolling process; excluding high fatigue performance concrete reinforcement bars and rods, and excluding other long products, such as round bars
- 7214 10 00 90Other bars and rods of iron or non-alloy steel, not further: forged, other
- 7214 20 00 10High fatigue performance concrete reinforcing bars and rods
- 7214 20 00 20Concrete reinforcement bars and rods excluding long products, such as round bars
- 7214 20 00 80Containing indentations, ribs, grooves or other: other, other
- 7214 30 00 10Concrete reinforcement bars and rods, containing indentations, ribs, grooves or other deformations produced during the rolling process; excluding high fatigue performance concrete reinforcement bars and rods, and excluding other long products, such as round bars
- 7214 30 00 90Other, of free-cutting steel: other
- 7214 91 10 10Concrete reinforcement bars and rods, containing indentations, ribs, grooves or other deformations produced during the rolling process; excluding high fatigue performance concrete reinforcement bars and rods, and excluding other long products, such as round bars
- 7214 91 10 90Containing by weight less than 0.25% of carbon: other
- 7214 91 90 10Concrete reinforcement bars and rods, containing indentations, ribs, grooves or other deformations produced during the rolling process; excluding high fatigue performance concrete reinforcement bars and rods, and excluding other long products, such as round bars
- 7214 91 90 90Containing by weight 0.25% or more of carbon: other
- 7214 99 10 10Bars and rods, containing indentations, ribs, grooves or other deformations produced during the rolling process; excluding high fatigue performance bars and rods, and excluding other long products, such as round bars
- 7214 99 10 90Of a type used for concrete reinforcement: other
- 7214 99 31 0080 mm or more
- 7214 99 39 00Less than 80 mm
- 7214 99 50 00Containing by weight less than 0.25% of carbon: other
- 7214 99 71 0080 mm or more
- 7214 99 79 00Less than 80 mm
- 7214 99 95 10Concrete reinforcement bars and rods, containing indentations, ribs, grooves or other deformations produced during the rolling process; excluding high fatigue performance concrete reinforcement bars and rods, and excluding other long products, such as round bars
- 7214 99 95 90Containing by weight 0.25% or more of carbon: other, other
7215 Other bars and rods of iron or non-alloy steel
- 7215 10 00 00Of free-cutting steel, not further worked than cold-formed or cold-finished
- 7215 50 11 00Of rectangular (other than square) cross-section
- 7215 50 19 00Containing by weight less than 0.25% of carbon: other
- 7215 50 80 00Containing by weight 0.25% or more of carbon
- 7215 90 00 10Hot-rolled, hot-drawn or extruded, not further worked than clad
- 7215 90 00 90Other bars and rods of iron or non-alloy steel: other, other
7216 Angles, shapes and sections of iron or non-alloy steel
- 7216 10 00 00U, i or h sections, not further worked than hot-rolled, hot-drawn or extruded, of a height of less than 80 mm
- 7216 21 00 00L or t sections, not further worked than hot-rolled: l sections
- 7216 22 00 00L or t sections, not further worked than hot-rolled: t sections
- 7216 31 10 00Of a height of 80 mm or more but not exceeding 220 mm
- 7216 31 90 00Of a height exceeding 220 mm
- 7216 32 11 00With parallel flange faces
- 7216 32 19 00Of a height of 80 mm or more but not exceeding 220 mm: other
- 7216 32 91 00With parallel flange faces
- 7216 32 99 00Of a height exceeding 220 mm: other
- 7216 33 10 00Of a height of 80 mm or more but not exceeding 180 mm
- 7216 33 90 00Of a height exceeding 180 mm
- 7216 40 10 00L or t sections, not further worked than hot-rolled: l sections
- 7216 40 90 00L or t sections, not further worked than hot-rolled: t sections
- 7216 50 10 00With a cross-section which is capable of being enclosed in a square the side of which is 80 mm
- 7216 50 91 10In the range up to 204 mm width
- 7216 50 91 90Other angles, shapes and sections, not further worked than: other, bulb flats, other
- 7216 50 99 00Other angles, shapes and sections, not further worked than: other, other
- 7216 61 10 00C, l, u, z, omega or open-ended sections
- 7216 61 90 00Obtained from flat-rolled products: other
- 7216 69 00 00Angles, shapes and sections, not further worked than: other
- 7216 91 10 00Cold-formed or cold-finished from flat-rolled products: profiled (ribbed) sheets
- 7216 91 80 00Cold-formed or cold-finished from flat-rolled products: other
- 7216 99 00 10Hot-rolled, hot-drawn or extruded, not further worked than clad
- 7216 99 00 90Angles, shapes and sections of iron or non-alloy steel: other, other, other
7217 Wire of iron or non-alloy steel
- 7217 10 10 00With a maximum cross-sectional dimension of less than 0.8 mm
- 7217 10 31 00Containing indentations, ribs, grooves or other deformations produced during the rolling process
- 7217 10 39 00With a maximum cross-sectional dimension of 0.8 mm or more: other
- 7217 10 50 00Containing by weight 0.25% or more but less than 0.6% of carbon
- 7217 10 90 10Of non-alloy steel, with a maximum cross-sectional dimension exceeding 3 mm
- 7217 10 90 90Containing by weight 0.6% or more of carbon: other
- 7217 20 10 00With a maximum cross-sectional dimension of less than 0.8 mm
- 7217 20 30 00With a maximum cross-sectional dimension of 0.8 mm or more
- 7217 20 50 00Containing by weight 0.25% or more but less than 0.6% of carbon
- 7217 20 90 10Of non-alloy steel, with a maximum cross-sectional dimension exceeding 3 mm
- 7217 20 90 90Containing by weight 0.6% or more of carbon: other
- 7217 30 41 00Containing by weight less than 0.25% of carbon: copper-coated
- 7217 30 49 00Containing by weight less than 0.25% of carbon: other
- 7217 30 50 00Containing by weight 0.25% or more but less than 0.6% of carbon
- 7217 30 90 00Containing by weight 0.6% or more of carbon
- 7217 90 20 00Containing by weight less than 0.25% of carbon
- 7217 90 50 00Containing by weight 0.25% or more but less than 0.6% of carbon
- 7217 90 90 00Containing by weight 0.6% or more of carbon
7218 Stainless steel in ingots or other primary forms; semi-finished products of stainless steel
- 7218 10 00 00Ingots and other primary forms
- 7218 91 10 00Containing by weight 2.5% or more of nickel
- 7218 91 80 00Containing by weight less than 2.5% of nickel
- 7218 99 11 00Rolled or obtained by continous casting
- 7218 99 19 00Stainless steel in ingots or other primary forms: other, other, of square cross-section, forged
- 7218 99 20 00Rolled or obtained by continuous casting
- 7218 99 80 00Stainless steel in ingots or other primary forms: other, other, other, forged
7219 Flat-rolled products of stainless steel, of a width of 600 mm or more
- 7219 11 00 10Of a thickness exceeding 10 mm: consigned from Türkiye
- 7219 11 00 90Of a thickness exceeding 10 mm: other
- 7219 12 10 10Containing by weight 2.5% or more of nickel: consigned from Türkiye
- 7219 12 10 90Containing by weight 2.5% or more of nickel: other
- 7219 12 90 10Containing by weight less than 2.5% of nickel: consigned from Türkiye
- 7219 12 90 90Containing by weight less than 2.5% of nickel: other
- 7219 13 10 10Containing by weight 2.5% or more of nickel: consigned from Türkiye
- 7219 13 10 90Containing by weight 2.5% or more of nickel: other
- 7219 13 90 10Containing by weight less than 2.5% of nickel: consigned from Türkiye
- 7219 13 90 90Containing by weight less than 2.5% of nickel: other
- 7219 14 10 10Containing by weight 2.5% or more of nickel: consigned from Türkiye
- 7219 14 10 90Containing by weight 2.5% or more of nickel: other
- 7219 14 90 10Containing by weight less than 2.5% of nickel: consigned from Türkiye
- 7219 14 90 90Containing by weight less than 2.5% of nickel: other
- 7219 21 10 00Containing by weight 2.5% or more of nickel
- 7219 21 90 00Containing by weight less than 2.5% of nickel
- 7219 22 10 10Containing by weight 2.5% or more of nickel: consigned from Türkiye
- 7219 22 10 90Containing by weight 2.5% or more of nickel: other
- 7219 22 90 10Containing by weight less than 2.5% of nickel: consigned from Türkiye
- 7219 22 90 90Containing by weight less than 2.5% of nickel: other
- 7219 23 00 10Of a thickness of 3 mm or more but less than 4.75 mm: consigned from Türkiye
- 7219 23 00 90Of a thickness of 3 mm or more but less than 4.75 mm: other
- 7219 24 00 10Of a thickness of less than 3 mm: consigned from Türkiye
- 7219 24 00 90Of a thickness of less than 3 mm: other
- 7219 31 00 10Of a thickness of 4.75 mm or more: consigned from Taiwan or Vietnam
- 7219 31 00 20Of a thickness of 4.75 mm or more: consigned from Türkiye
- 7219 31 00 90Of a thickness of 4.75 mm or more: other
- 7219 32 10 10Containing by weight 2.5% or more of nickel: consigned from Taiwan or Vietnam
- 7219 32 10 20Containing by weight 2.5% or more of nickel: consigned from Türkiye
- 7219 32 10 90Containing by weight 2.5% or more of nickel: other
- 7219 32 90 10Containing by weight less than 2.5% of nickel: consigned from Taiwan or Vietnam
- 7219 32 90 20Containing by weight less than 2.5% of nickel: consigned from Türkiye
- 7219 32 90 90Containing by weight less than 2.5% of nickel: other
- 7219 33 10 10Containing by weight 2.5% or more of nickel: consigned from Taiwan or Vietnam
- 7219 33 10 20Containing by weight 2.5% or more of nickel: consigned from Türkiye
- 7219 33 10 90Containing by weight 2.5% or more of nickel: other
- 7219 33 90 10Containing by weight less than 2.5% of nickel: consigned from Taiwan or Vietnam
- 7219 33 90 20Containing by weight less than 2.5% of nickel: consigned from Türkiye
- 7219 33 90 90Containing by weight less than 2.5% of nickel: other
- 7219 34 10 10Containing by weight 2.5% or more of nickel: consigned from Taiwan or Vietnam
- 7219 34 10 20Containing by weight 2.5% or more of nickel: consigned from Türkiye
- 7219 34 10 90Containing by weight 2.5% or more of nickel: other
- 7219 34 90 10Containing by weight less than 2.5% of nickel: consigned from Taiwan or Vietnam
- 7219 34 90 20Containing by weight less than 2.5% of nickel: consigned from Türkiye
- 7219 34 90 90Containing by weight less than 2.5% of nickel: other
- 7219 35 10 10Containing by weight 2.5% or more of nickel: consigned from Taiwan or Vietnam
- 7219 35 10 20Containing by weight 2.5% or more of nickel: consigned from Türkiye
- 7219 35 10 90Containing by weight 2.5% or more of nickel: other
- 7219 35 90 10Containing by weight less than 2.5% of nickel: consigned from Taiwan or Vietnam
- 7219 35 90 20Containing by weight less than 2.5% of nickel: consigned from Türkiye
- 7219 35 90 90Containing by weight less than 2.5% of nickel: other
- 7219 90 20 10Flat-rolled products of stainless steel, of a width of 600: other, perforated, consigned from Taiwan or Vietnam
- 7219 90 20 20Flat-rolled products of stainless steel, of a width of 600: other, perforated, consigned from Türkiye
- 7219 90 20 90Flat-rolled products of stainless steel, of a width of 600: other, perforated, other
- 7219 90 80 10Flat-rolled products of stainless steel, of a width of 600: other, other, consigned from Taiwan or Vietnam
- 7219 90 80 20Flat-rolled products of stainless steel, of a width of 600: other, other, consigned from Türkiye
- 7219 90 80 90Flat-rolled products of stainless steel, of a width of 600: other, other, other
7220 Flat-rolled products of stainless steel, of a width of less than 600 mm
- 7220 11 00 10Of a thickness of 4.75 mm or more: consigned from Türkiye
- 7220 11 00 90Of a thickness of 4.75 mm or more: other
- 7220 12 00 10Of a thickness of less than 4.75 mm: consigned from Türkiye
- 7220 12 00 90Of a thickness of less than 4.75 mm: other
- 7220 20 21 102.5% or more of nickel: consigned from Taiwan or Vietnam
- 7220 20 21 202.5% or more of nickel: consigned from Türkiye
- 7220 20 21 902.5% or more of nickel: other
- 7220 20 29 10Less than 2.5% of nickel: consigned from Taiwan or Vietnam
- 7220 20 29 20Less than 2.5% of nickel: consigned from Türkiye
- 7220 20 29 90Less than 2.5% of nickel: other
- 7220 20 41 102.5% or more of nickel: consigned from Taiwan or Vietnam
- 7220 20 41 202.5% or more of nickel: consigned from Türkiye
- 7220 20 41 902.5% or more of nickel: other
- 7220 20 49 10Less than 2.5% of nickel: consigned from Taiwan or Vietnam
- 7220 20 49 20Less than 2.5% of nickel: consigned from Türkiye
- 7220 20 49 90Less than 2.5% of nickel: other
- 7220 20 81 102.5% or more of nickel: consigned from Taiwan or Vietnam
- 7220 20 81 202.5% or more of nickel: consigned from Türkiye
- 7220 20 81 902.5% or more of nickel: other
- 7220 20 89 10Less than 2.5% of nickel: consigned from Taiwan or Vietnam
- 7220 20 89 20Less than 2.5% of nickel: consigned from Türkiye
- 7220 20 89 90Less than 2.5% of nickel: other
- 7220 90 20 10Flat-rolled products of stainless steel, of a width of less: other, perforated, consigned from Taiwan or Vietnam
- 7220 90 20 20Flat-rolled products of stainless steel, of a width of less: other, perforated, consigned from Türkiye
- 7220 90 20 90Flat-rolled products of stainless steel, of a width of less: other, perforated, other
- 7220 90 80 10Flat-rolled products of stainless steel, of a width of less: other, other, consigned from Taiwan or Vietnam
- 7220 90 80 20Flat-rolled products of stainless steel, of a width of less: other, other, consigned from Türkiye
- 7220 90 80 90Flat-rolled products of stainless steel, of a width of less: other, other, other
7221 Bars and rods, hot-rolled, in irregularly wound coils, of stainless steel
7222 Other bars and rods of stainless steel; angles, shapes and sections of stainless steel
- 7222 11 11 002.5% or more of nickel
- 7222 11 19 00Less than 2.5% of nickel
- 7222 11 81 002.5% or more of nickel
- 7222 11 89 00Less than 2.5% of nickel
- 7222 19 10 00Containing by weight 2.5% or more of nickel
- 7222 19 90 00Containing by weight less than 2.5% of nickel
- 7222 20 11 002.5% or more of nickel
- 7222 20 19 00Less than 2.5% of nickel
- 7222 20 21 002.5% or more of nickel
- 7222 20 29 00Less than 2.5% of nickel
- 7222 20 31 002.5% or more of nickel
- 7222 20 39 00Less than 2.5% of nickel
- 7222 20 81 002.5% or more of nickel
- 7222 20 89 00Less than 2.5% of nickel
- 7222 30 51 002.5% or more of nickel
- 7222 30 91 00Less than 2.5% of nickel
- 7222 30 97 10Hot-rolled, hot-drawn or extruded, not further worked than clad
- 7222 30 97 90Other bars and rods: other, other
- 7222 40 10 00Not further worked than hot-rolled, hot-drawn or extruded
- 7222 40 50 00Not further worked than cold-formed or cold-finished
- 7222 40 90 10Hot-rolled, hot-drawn or extruded, not further worked than clad
- 7222 40 90 90Angles, shapes and sections: other, other
7223 Wire of stainless steel
- 7223 00 11 00Containing by weight 28% or more but not more than 31% of nickel and 20% or more but not more than 22% of chromium
- 7223 00 19 00Containing by weight 2.5% or more of nickel: other
- 7223 00 91 00Containing by weight 13% or more but not more than 25% of chromium and 3.5% or more but not more than 6% of aluminium
- 7223 00 99 00Containing by weight less than 2.5% of nickel: other
7224 Other alloy steel in ingots or other primary forms; semi-finished products of other alloy steel
- 7224 10 10 00Ingots and other primary forms: of tool steel
- 7224 10 90 00Ingots and other primary forms: other
- 7224 90 02 29Of rectangular (including square) cross-section
- 7224 90 02 89Hot-rolled or obtained by continuous casting
- 7224 90 02 99Other alloy steel in ingots or other primary forms: other, of tool steel, other, other
- 7224 90 03 00The width measuring less than twice the thickness: of high-speed steel
- 7224 90 05 00Containing by weight not more than 0.7% of carbon, 0.5% or more but not more than 1.2% of manganese and 0.6% or more but not more than 2.3% of silicon; containing by weight 0.0008% or more of boron with any other element less than the minimum content referred to in note 1(f) to this chapter
- 7224 90 07 00The width measuring less than twice the thickness: other
- 7224 90 14 00Hot-rolled or obtained by continuous casting: other
- 7224 90 18 00Of rectangular (including square) cross-section: forged
- 7224 90 31 00Containing by weight not less than 0.9% but not more than 1.15% of carbon, not less than 0.5% but not more than 2% of chromium and, if present, not more than 0.5% of molybdenum
- 7224 90 38 00Hot-rolled or obtained by continuous casting: other
- 7224 90 90 00Other alloy steel in ingots or other primary forms: other, other, other, forged
7225 Flat-rolled products of other alloy steel, of a width of 600 mm or more
- 7225 11 00 11With a maximum core loss not higher than 0.7 w/kg
- 7225 11 00 12With a maximum core loss higher than 0.7 w/kg but not higher than 0.9 w/kg
- 7225 11 00 15With a maximum core loss higher than 0.9 w/kg but not higher than 1.05 w/kg
- 7225 11 00 19With a maximum core loss higher than 1.05 w/kg
- 7225 11 00 90Flat-rolled products of other alloy steel, of a width: of silicon-electrical steel, grain-oriented, other
- 7225 19 10 10Products clad, plated or coated, not in coils, without patterns in relief, of a thickness exceeding 10 mm and products clad, plated or coated, not in coils, without patterns in relief, of a thickness of 4.75 mm or more but not exceeding 10 mm and of a width of 2 050 mm or more
- 7225 19 10 90Flat-rolled products of other alloy steel, of a width: of silicon-electrical steel, other, hot-rolled, other
- 7225 19 90 00Flat-rolled products of other alloy steel, of a width: of silicon-electrical steel, other, cold-rolled
- 7225 30 10 00Other, not further worked than hot-rolled, in coils: of tool steel
- 7225 30 30 10Not further worked than rolled; not further worked than surface-treated, including cladding or simply cut into shapes other than rectangular (including square)
- 7225 30 30 90Other, not further worked than hot-rolled, in coils: of high-speed steel, other
- 7225 30 90 00Other, not further worked than hot-rolled, in coils: other
- 7225 40 12 30Of a thickness of less than 4.75 mm
- 7225 40 12 90Other, not further worked than hot-rolled, not in coils: of tool steel, other
- 7225 40 15 10Not further worked than rolled; not further worked than surface-treated, including cladding or simply cut into shapes other than rectangular (including square)
- 7225 40 15 90Other, not further worked than hot-rolled, not in coils: of high-speed steel, other
- 7225 40 40 00Of a thickness exceeding 10 mm
- 7225 40 60 10Of a width of 2 050 mm or more
- 7225 40 60 90Of a thickness of 4.75 mm or more but not exceeding 10 mm: other
- 7225 40 90 00Of a thickness of less than 4.75 mm
- 7225 50 20 10Not further worked than rolled; not further worked than surface-treated, including cladding or simply cut into shapes other than rectangular (including square)
- 7225 50 20 90Other, not further worked than cold-rolled (cold-reduced): of high-speed steel, other
- 7225 50 80 00Other, not further worked than cold-rolled (cold-reduced): other
- 7225 91 00 10Not further worked than surface-treated, including cladding or simply cut into shapes other than rectangular (including square)
- 7225 91 00 90Electrolytically plated or coated with zinc: other
- 7225 92 00 20Aluminium killed; plated or coated by hot dip galvanisation with zinc and/or with aluminium, and no other metal; chemically passivated; containing by weight: 0.015% or more but not more than 0.170% of carbon, 0.015% or more but not more than 0.100% of aluminium, not more than 0.045% of niobium, not more than 0.010% of titanium and not more than 0.010% of vanadium; presented in coils, cut-to-length sheets and narrow strips
- 7225 92 00 30Plated or coated by hot dip galvanisation, whether or not alloyed with silicon; chemically passivated; with or without any additional surface treatment such as oiling or sealing; containing by weight: not more than 0.5% of carbon, not more than 1.1% of aluminium, not more than 0.12% of niobium, not more than 0.17% of titanium and not more than 0.15% of vanadium; presented in coils, cut-to-length sheets and narrow strips
- 7225 92 00 80Not further worked than surface-treated, including cladding: other
- 7225 92 00 90Otherwise plated or coated with zinc: other
- 7225 99 00 11Painted, varnished or coated with plastics on at least one side, excluding products with a final coating of zinc-dust (a zinc-rich paint, containing by weight 70% or more of zinc) and excluding products with a substrate with a metallic coating of chromium or tin
- 7225 99 00 22Other, aluminium killed; plated or coated by hot dip galvanisation with zinc and/or with aluminium, and no other metal; chemically passivated; containing by weight: 0.015% or more but not more than 0.170% of carbon, 0.015% or more but not more than 0.100% of aluminium, not more than 0.045% of niobium, not more than 0.010% of titanium and not more than 0.010% of vanadium; presented in coils, cut-to-length sheets and narrow strips
- 7225 99 00 23Plated or coated by hot dip galvanisation with magnesium and/or aluminium, whether or not alloyed with zinc, whether or not alloyed with silicon; chemically passivated; with additional surface treatment such as oiling or sealing; containing by weight: not more than 0.5% of carbon, not more than 1.1% of aluminium, not more than 0.12% of niobium, not more than 0.17% of titanium and not more than 0.15% of vanadium; presented in coils, cut-to-length sheets and narrow strips
- 7225 99 00 25Not further worked than surface-treated, including cladding: other
- 7225 99 00 41Plated or coated by hot dip galvanisation with magnesium and/or aluminium, whether or not alloyed with zinc, whether or not alloyed with silicon; chemically passivated; with additional surface treatment such as oiling or sealing; containing by weight: not more than 0.5% of carbon, not more than 1.1% of aluminium, not more than 0.12% of niobium, not more than 0.17% of titanium and not more than 0.15% of vanadium; presented in coils, cut-to-length sheets and narrow strips
- 7225 99 00 45Other, of a thickness exceeding 10 mm or of a thickness: other
- 7225 99 00 91Painted, varnished or coated with plastics on at least one side, excluding so-called " sandwich panels" of a kind used for building applications and consisting of two outer metal sheets with a stabilising core of insulation material sandwiched between them, excluding those products with a final coating of zinc-dust (a zinc-rich paint, containing by weight 70% or more of zinc) and excluding products with a substrate with a metallic coating of chromium or tin
- 7225 99 00 92Other, aluminium killed; plated or coated by hot dip galvanisation with zinc and/or with aluminium, and no other metal; chemically passivated; containing by weight: 0.015% or more but not more than 0.170% of carbon, 0.015% or more but not more than 0.100% of aluminium, not more than 0.045% of niobium, not more than 0.010% of titanium and not more than 0.010% of vanadium; presented in coils, cut-to-length sheets and narrow strips
- 7225 99 00 93Plated or coated by hot dip galvanisation with magnesium and/or aluminium, whether or not alloyed with zinc, whether or not alloyed with silicon; chemically passivated; with additional surface treatment such as oiling or sealing; containing by weight: not more than 0.5% of carbon, not more than 1.1% of aluminium, not more than 0.12% of niobium, not more than 0.17% of titanium and not more than 0.15% of vanadium; presented in coils, cut-to-length sheets and narrow strips
- 7225 99 00 95Flat-rolled products of other alloy steel, of a width: other, other, other, other
7226 Flat-rolled products of other alloy steel, of a width of less than 600 mm
- 7226 11 00 12With a maximum core loss not higher than 0.7 w/kg
- 7226 11 00 13With a maximum core loss higher than 0.7 w/kg but not higher than 0.9 w/kg
- 7226 11 00 14With a maximum core loss higher than 0.9 w/kg but not higher than 1.05 w/kg
- 7226 11 00 16With a maximum core loss higher than 1.05 w/kg
- 7226 11 00 19Of a width exceeding 500 mm: other
- 7226 11 00 92With a maximum core loss not higher than 0.7 w/kg
- 7226 11 00 93With a maximum core loss higher than 0.7 w/kg but not higher than 0.9 w/kg
- 7226 11 00 94With a maximum core loss higher than 0.9 w/kg but not higher than 1.05 w/kg
- 7226 11 00 96With a maximum core loss higher than 1.05 w/kg
- 7226 11 00 99Of a width not exceeding 500 mm: other
- 7226 19 10 10Products clad, plated or coated
- 7226 19 10 91Of a width not exceeding 350 mm and of a thickness of 50 mm or more
- 7226 19 10 95Not further worked than hot-rolled: other, other
- 7226 19 80 10Of a width exceeding 500 mm
- 7226 19 80 90Of a width not exceeding 500 mm
- 7226 20 00 10Not further worked than hot-rolled; of a width not exceeding 500 mm, hot-rolled, not further worked than clad; of a width exceeding 500 mm, not further worked than cold-rolled (cold-reduced) or not further worked than surface-treated, including cladding
- 7226 20 00 90Flat-rolled products of other alloy steel, of a width: of high-speed steel, other
- 7226 91 20 00Not further worked than hot-rolled: of tool steel
- 7226 91 91 11Of a width not exceeding 350 mm and of a thickness of 50 mm or more
- 7226 91 91 19Of a thickness of 4.75 mm or more: other
- 7226 91 99 00Of a thickness of less than 4.75 mm
- 7226 92 00 10Of a width exceeding 500 mm
- 7226 92 00 90Of a width not exceeding 500 mm
- 7226 99 10 00Electrolytically plated or coated with zinc
- 7226 99 30 10Aluminium killed; plated or coated by hot dip galvanisation with zinc and/or with aluminium, and no other metal; chemically passivated; containing by weight: 0.015% or more but not more than 0.170% of carbon, 0.015% or more but not more than 0.100% of aluminium, not more than 0.045% of niobium, not more than 0.010% of titanium and not more than 0.010% of vanadium; presented in coils, cut-to-length sheets and narrow strips
- 7226 99 30 30Plated or coated by hot dip galvanisation, whether or not alloyed with silicon; chemically passivated; with or without any additional surface treatment such as oiling or sealing; containing by weight: not more than 0.5% of carbon, not more than 1.1% of aluminium, not more than 0.12% of niobium, not more than 0.17% of titanium and not more than 0.15% of vanadium; presented in coils, cut-to-length sheets and narrow strips
- 7226 99 30 90Otherwise plated or coated with zinc: other
- 7226 99 70 11Painted, varnished or coated with plastics on at least one side, excluding products with a final coating of zinc-dust (a zinc-rich paint, containing by weight 70% or more of zinc) and excluding products with a substrate with a metallic coating of chromium or tin
- 7226 99 70 13Plated or coated by hot dip galvanisation with magnesium and/or aluminium, whether or not alloyed with zinc, whether or not alloyed with silicon; chemically passivated; with or without additional surface treatment such as oiling or sealing; containing by weight: not more than 0.5% of carbon, not more than 1.1% of aluminium, not more than 0.12% of niobium, not more than 0.17% of titanium and not more than 0.15% of vanadium; presented in coils, cut-to-length sheets and narrow strips
- 7226 99 70 19Of a width not exceeding 500 mm, hot-rolled, not further: other
- 7226 99 70 91Painted, varnished or coated with plastics on at least one side, excluding so-called " sandwich panels" of a kind used for building applications and consisting of two outer metal sheets with a stabilising core of insulation material sandwiched between them, excluding those products with a final coating of zinc-dust (a zinc-rich paint, containing by weight 70% or more of zinc) and excluding products with a substrate with a metallic coating of chromium or tin
- 7226 99 70 93Plated or coated by hot dip galvanisation with magnesium and/or aluminium, whether or not alloyed with zinc, whether or not alloyed with silicon; chemically passivated; with or without additional surface treatment such as oiling or sealing; containing by weight: not more than 0.5% of carbon, not more than 1.1% of aluminium, not more than 0.12% of niobium, not more than 0.17% of titanium and not more than 0.15% of vanadium; presented in coils, cut-to-length sheets and narrow strips
- 7226 99 70 94Other, aluminium killed; plated or coated by hot dip galvanisation with zinc and/or with aluminium, and no other metal; chemically passivated; containing by weight: 0.015% or more but not more than 0.170% of carbon, 0.015% or more but not more than 0.100% of aluminium, not more than 0.045% of niobium, not more than 0.010% of titanium and not more than 0.010% of vanadium; presented in coils, cut-to-length sheets and narrow strips
- 7226 99 70 96Flat-rolled products of other alloy steel, of a width: other, other, other, other, other
7227 Bars and rods, hot-rolled, in irregularly wound coils, of other alloy steel
- 7227 10 00 00Bars and rods, hot-rolled, in irregularly wound coils: of high-speed steel
- 7227 20 00 00Bars and rods, hot-rolled, in irregularly wound coils: of silico-manganese steel
- 7227 90 10 00Containing by weight 0.0008% or more of boron with any other element less than the minimum content referred to in note 1(f) to this chapter
- 7227 90 50 00Containing by weight 0.9% or more but not more than 1.15% of carbon, 0.5% or more but not more than 2% of chromium and, if present, not more than 0.5% of molybdenum
- 7227 90 95 00Bars and rods, hot-rolled, in irregularly wound coils: other, other
7228 Other bars and rods of other alloy steel; angles, shapes and sections, of other alloy steel; hollow drill bars and rods, of alloy or non-alloy steel
- 7228 10 20 00Not further worked than hot-rolled, hot-drawn or extruded; hot-rolled, hot-drawn or extruded, not further worked than clad
- 7228 10 50 00Bars and rods, of high-speed steel: forged
- 7228 10 90 00Bars and rods, of high-speed steel: other
- 7228 20 10 10Not further worked than hot-rolled, hot-drawn or extruded
- 7228 20 10 91Hot-rolled, hot-drawn or extruded, not further worked than clad
- 7228 20 10 99Of rectangular: other, other
- 7228 20 91 00Not further worked than hot-rolled, hot-drawn or extruded; hot-rolled, hot-drawn or extruded, not further worked than clad
- 7228 20 99 00Bars and rods, of silico-manganese steel: other, other
- 7228 30 20 00Other bars and rods, not further worked than hot-rolled: of tool steel
- 7228 30 41 00Of circular cross-section of a diameter of 80 mm or more
- 7228 30 49 00Containing by weight 0.9% or more but not more than 1.15%: other
- 7228 30 61 0080 mm or more
- 7228 30 69 11Reinforcing bars and rods, containing indentations, ribs, grooves or other deformations
- 7228 30 69 99Less than 80 mm: other
- 7228 30 70 00Of rectangular (other than square) cross-section, hot-rolled on four faces
- 7228 30 89 00Other bars and rods, not further worked than hot-rolled: other, other
- 7228 40 10 00Other bars and rods, not further worked than forged: of tool steel
- 7228 40 90 00Other bars and rods, not further worked than forged: other
- 7228 50 20 00Other bars and rods, not further worked than cold-formed: of tool steel
- 7228 50 40 00Containing by weight 0.9% or more but not more than 1.15% of carbon, 0.5% or more but not more than 2% of chromium and, if present, not more than 0.5% of molybdenum
- 7228 50 61 0080 mm or more
- 7228 50 69 00Less than 80 mm
- 7228 50 80 00Other bars and rods, not further worked than cold-formed: other, other
- 7228 60 20 10Hot-rolled, hot-drawn or extruded, not further worked than clad
- 7228 60 20 90Other bars and rods: of tool steel, other
- 7228 60 80 10Hot-rolled, hot-drawn or extruded, not further worked than clad
- 7228 60 80 90Other bars and rods: other, other
- 7228 70 10 00Not further worked than hot-rolled, hot-drawn or extruded
- 7228 70 90 10Hot-rolled, hot-drawn or extruded, not further worked than clad
- 7228 70 90 90Angles, shapes and sections: other, other
- 7228 80 00 00Hollow drill bars and rods
7229 Wire of other alloy steel
- 7229 20 00 10With a cross section with a diameter of 0.6mm to 4mm, containing by weight not more than 0.2% of carbon, 0.6% or more but not more than 1.4% of silicon, and 0.9% or more but not more than 1.9% of manganese, but no other element in a proportion that would give the steel the characteristics of another alloy steel, whether coated with copper or bronze or wax/oil based lubricant or not
- 7229 20 00 90Wire of other alloy steel: of silico-manganese steel, other
- 7229 90 20 00Wire of other alloy steel: other, of high-speed steel
- 7229 90 50 00Containing by weight 0.9% or more but not more than 1.15% of carbon, 0.5% or more but not more than 2% of chromium and, if present, not more than 0.5% of molybdenum
- 7229 90 90 00Wire of other alloy steel: other, other