UK Global Tariff
UK Global Tariff, chapter 87: Vehicles other than railway or tramway rolling stock, and parts and accessories thereof
- 367Tariff lines
- 0%–18%Rate
Chapter 87 has 367 lines in the UK Global Tariff, spread over 16 headings.
Rates run from 0% to 18%, averaging 5.2%; 44 lines are duty-free.
The most detailed heading is 8708 (parts and accessories of the motor vehicles of headings 8701 to 8705) with 137 lines.
The most common rate is 4%, on 106 lines.
The highest is 18% on 8706 00 11 00 (for vehicles of heading 8702 or 8704).
8701 Tractors (other than tractors of heading 8709)
- 8701 10 00 00Tractors (other than tractors of heading 8709): single axle tractors
- 8701 21 10 00With only compression-ignition internal combustion piston: new
- 8701 21 90 00With only compression-ignition internal combustion piston: used
- 8701 22 10 00With both compression-ignition internal combustion piston: new
- 8701 22 90 00With both compression-ignition internal combustion piston: used
- 8701 23 10 00With both spark-ignition internal combustion piston engine: new
- 8701 23 90 00With both spark-ignition internal combustion piston engine: used
- 8701 24 10 00With only electric motor for propulsion: new
- 8701 24 90 00With only electric motor for propulsion: used
- 8701 29 00 00Road tractors for semi-trailers: other
- 8701 30 00 00Tractors (other than tractors of heading 8709): track-laying tractors
- 8701 91 10 00Agricultural tractors and forestry tractors, wheeled
- 8701 91 90 00Not exceeding 18 kw: other
- 8701 92 10 00Agricultural tractors and forestry tractors, wheeled
- 8701 92 90 00Exceeding 18 kw but not exceeding 37 kw: other
- 8701 93 10 00Agricultural tractors and forestry tractors, wheeled
- 8701 93 90 00Exceeding 37 kw but not exceeding 75 kw: other
- 8701 94 10 00Agricultural tractors and forestry tractors, wheeled
- 8701 94 90 00Exceeding 75 kw but not exceeding 130 kw: other
- 8701 95 10 00Agricultural tractors and forestry tractors, wheeled
- 8701 95 90 00Other, of an engine power: exceeding 130 kw, other
8702 Motor vehicles for the transport of ten or more persons, including the driver
- 8702 10 11 00Of a cylinder capacity exceeding 2 500 cm3: new
- 8702 10 19 00Of a cylinder capacity exceeding 2 500 cm3: used
- 8702 10 91 00Of a cylinder capacity not exceeding 2 500 cm3: new
- 8702 10 99 00Of a cylinder capacity not exceeding 2 500 cm3: used
- 8702 20 10 00Of a cylinder capacity exceeding 2 500 cm3
- 8702 20 90 00Of a cylinder capacity not exceeding 2 500 cm3
- 8702 30 10 00Of a cylinder capacity exceeding 2 800 cm3
- 8702 30 90 00Of a cylinder capacity not exceeding 2 800 cm3
- 8702 40 00 00With only electric motor for propulsion
- 8702 90 11 00Of a cylinder capacity exceeding 2 800 cm3: new
- 8702 90 19 00Of a cylinder capacity exceeding 2 800 cm3: used
- 8702 90 31 00Of a cylinder capacity not exceeding 2 800 cm3: new
- 8702 90 39 00Of a cylinder capacity not exceeding 2 800 cm3: used
- 8702 90 90 00Motor vehicles for the transport of ten or more persons: other, with other engines
8703 Motor cars and other motor vehicles principally designed for the transport of persons (other than those of heading 8702), including station wagons and racing cars
- 8703 10 11 00Vehicles specially designed for travelling on snow, with compression-ignition internal combustion piston engine (diesel or semi-diesel), or with spark-ignition internal combustion piston engine
- 8703 10 18 00Vehicles specially designed for travelling on snow: other
- 8703 21 10 00Of a cylinder capacity not exceeding 1 000 cm3: new
- 8703 21 90 00Of a cylinder capacity not exceeding 1 000 cm3: used
- 8703 22 10 00Of a cylinder capacity exceeding 1 000 cm3: new
- 8703 22 90 00Of a cylinder capacity exceeding 1 000 cm3: used
- 8703 23 11 00Of a cylinder capacity exceeding 1 500 cm3: new, motor caravans
- 8703 23 19 00Of a cylinder capacity exceeding 1 500 cm3: new, other
- 8703 23 90 00Of a cylinder capacity exceeding 1 500 cm3: used
- 8703 24 10 00Of a cylinder capacity exceeding 3 000 cm3: new
- 8703 24 90 00Of a cylinder capacity exceeding 3 000 cm3: used
- 8703 31 10 00Of a cylinder capacity not exceeding 1 500 cm3: new
- 8703 31 90 00Of a cylinder capacity not exceeding 1 500 cm3: used
- 8703 32 11 00Of a cylinder capacity exceeding 1 500 cm3: new, motor caravans
- 8703 32 19 00Of a cylinder capacity exceeding 1 500 cm3: new, other
- 8703 32 90 00Of a cylinder capacity exceeding 1 500 cm3: used
- 8703 33 11 00Of a cylinder capacity exceeding 2 500 cm3: new, motor caravans
- 8703 33 19 00Of a cylinder capacity exceeding 2 500 cm3: new, other
- 8703 33 90 00Of a cylinder capacity exceeding 2 500 cm3: used
- 8703 40 10 10Of a cylinder capacity not exceeding 1 000 cm3
- 8703 40 10 90Other vehicles, with both spark-ignition internal: new, other
- 8703 40 90 10Of a cylinder capacity not exceeding 1 000 cm3
- 8703 40 90 90Other vehicles, with both spark-ignition internal: used, other
- 8703 50 00 00Other vehicles, with both compression-ignition internal combustion piston engine (diesel or semi-diesel) and electric motor as motors for propulsion, other than those capable of being charged by plugging to external source of electric power
- 8703 60 10 10Of a cylinder capacity not exceeding 1 000 cm3
- 8703 60 10 90Other vehicles, with both spark-ignition internal: new, other
- 8703 60 90 10Of a cylinder capacity not exceeding 1 000 cm3
- 8703 60 90 90Other vehicles, with both spark-ignition internal: used, other
- 8703 70 00 00Other vehicles, with both compression-ignition internal combustion piston engine (diesel or semi-diesel) and electric motor as motors for propulsion, capable of being charged by plugging to external source of electric power
- 8703 80 10 10New battery electric vehicles, principally designed for the transport of nine or less persons, including the driver, excluding l category vehicles according to regulation (eu) no 168/2013 and motorcycles, propelled (regardless of the number of wheels set in motion) solely by one or more electric motors, including those with an internal combustion range extender (an auxiliary power unit)
- 8703 80 10 90Other vehicles, with only electric motor for propulsion: new, other
- 8703 80 90 00Other vehicles, with only electric motor for propulsion: used
- 8703 90 00 00Motor cars and other motor vehicles principally designed: other
8704 Motor vehicles for the transport of goods
- 8704 10 10 00With compression-ignition internal combustion piston engine (diesel or semi-diesel), or with spark-ignition internal combustion piston engine
- 8704 10 90 00Dumpers designed for off-highway use: other
- 8704 21 10 00Specially designed for the transport of highly radioactive materials
- 8704 21 31 00With engines of a cylinder capacity exceeding 2 500 cm3: new
- 8704 21 39 00With engines of a cylinder capacity exceeding 2 500 cm3: used
- 8704 21 91 00With engines of a cylinder capacity not exceeding 2 500 cm3: new
- 8704 21 99 00With engines of a cylinder capacity not exceeding 2 500 cm3: used
- 8704 22 10 00Specially designed for the transport of highly radioactive materials
- 8704 22 91 00Of a gross vehicle weight exceeding 5 tonnes: other, new
- 8704 22 99 00Of a gross vehicle weight exceeding 5 tonnes: other, used
- 8704 23 10 00Specially designed for the transport of highly radioactive materials
- 8704 23 91 00Of a gross vehicle weight exceeding 20 tonnes: other, new
- 8704 23 99 00Of a gross vehicle weight exceeding 20 tonnes: other, used
- 8704 31 10 00Specially designed for the transport of highly radioactive materials
- 8704 31 31 00With engines of a cylinder capacity exceeding 2 800 cm3: new
- 8704 31 39 00With engines of a cylinder capacity exceeding 2 800 cm3: used
- 8704 31 91 00With engines of a cylinder capacity not exceeding 2 800 cm3: new
- 8704 31 99 00With engines of a cylinder capacity not exceeding 2 800 cm3: used
- 8704 32 10 00Specially designed for the transport of highly radioactive materials
- 8704 32 91 00Of a gross vehicle weight exceeding 5 tonnes: other, new
- 8704 32 99 00Of a gross vehicle weight exceeding 5 tonnes: other, used
- 8704 41 10 00Specially designed for the transport of highly radioactive materials
- 8704 41 31 00With engines of a cylinder capacity exceeding 2 500 m³: new
- 8704 41 39 00With engines of a cylinder capacity exceeding 2 500 m³: used
- 8704 41 91 00With engines of a cylinder capacity not exceeding 2 500 cm³: new
- 8704 41 99 00With engines of a cylinder capacity not exceeding 2 500 cm³: used
- 8704 42 10 00Specially designed for the transport of highly radioactive materials
- 8704 42 91 00Of a gross vehicle weight exceeding 5 tonnes: other, new
- 8704 42 99 00Of a gross vehicle weight exceeding 5 tonnes: other, used
- 8704 43 10 00Specially designed for the transport of highly radioactive materials
- 8704 43 91 00Of a gross vehicle weight exceeding 20 tonnes: other, new
- 8704 43 99 00Of a gross vehicle weight exceeding 20 tonnes: other, used
- 8704 51 10 00Specially designed for the transport of highly radioactive materials
- 8704 51 31 00With engines of a cylinder capacity exceeding 2 800 cm³: new
- 8704 51 39 00With engines of a cylinder capacity exceeding 2 800 cm³: used
- 8704 51 91 00With engines of a cylinder capacity not exceeding 2 800 cm³: new
- 8704 51 99 00With engines of a cylinder capacity not exceeding 2 800 cm³: used
- 8704 52 10 00Specially designed for the transport of highly radioactive materials
- 8704 52 91 00Of a gross vehicle weight exceeding 5 tonnes: other, new
- 8704 52 99 00Of a gross vehicle weight exceeding 5 tonnes: other, used
- 8704 60 00 00Other with only electric motor for propulsion
- 8704 90 00 00Motor vehicles for the transport of goods: other
8705 Special purpose motor vehicles, other than those principally designed for the transport of persons or goods (for example, breakdown lorries, crane lorries, fire fighting vehicles, concrete-mixer lorries, road sweeper lorries, spraying lorries, mobile workshops, mobile radiological units)
- 8705 10 00 11New mobile cranes, meaning cable-controlled or hydraulic-powered cranes, designed for the lifting, lowering and horizontal movement of materials on land, with a lifting capacity of at least 30 tonnes, mounted on self-propelled vehicles, regardless of their propulsion systemmobile cranes
- 8705 10 00 90Special purpose motor vehicles, other than those: crane lorries, other
- 8705 20 00 00Special purpose motor vehicles, other than those: mobile drilling derricks
- 8705 30 00 00Special purpose motor vehicles, other than those: fire fighting vehicles
- 8705 40 00 00Special purpose motor vehicles, other than those: concrete-mixer lorries
- 8705 90 30 00Special purpose motor vehicles, other than those: other, concrete-pumping vehicles
- 8705 90 80 00Special purpose motor vehicles, other than those: other, other
8706 Chassis fitted with engines, for the motor vehicles of headings 8701 to 8705
8707 Bodies (including cabs), for the motor vehicles of headings 8701 to 8705
- 8707 10 10 00For industrial assembly purposes
- 8707 10 90 00For the vehicles of heading 8703: other
- 8707 90 10 00For the industrial assembly of: pedestrian-controlled tractors of subheading 8701 10; vehicles of heading 8704 with either a compression-ignition internal combustion piston engine (diesel or semi-diesel) of a cylinder capacity not exceeding 2 500 cm3 or with a spark-ignition internal combustion piston engine of a cylinder capacity not exceeding 2 800 cm3; special purpose motor vehicles of heading 8705
- 8707 90 90 00Bodies (including cabs), for the motor vehicles of headings: other, other
8708 Parts and accessories of the motor vehicles of headings 8701 to 8705
- 8708 10 10 10Plastic cover for filling the space between the fog lights and the bumper whether or not with a chrome strip for use in the manufacture of goods of chapter 87
- 8708 10 10 90For the industrial assembly of: other
- 8708 10 90 10Plastic cover for filling the space between the fog lights and the bumper whether or not with a chrome strip for use in the manufacture of goods of chapter 87
- 8708 10 90 90Bumpers and parts thereof: other, other
- 8708 21 10 00For the industrial assembly of: vehicles of heading 8703; vehicles of heading 8704 with either a compression-ignition internal combustion piston engine (diesel or semi-diesel) of a cylinder capacity not exceeding 2 500 cm3 or with a spark-ignition internal combustion piston engine of a cylinder capacity not exceeding 2 800 cm3; vehicles of heading 8705
- 8708 21 90 00Other parts and accessories of bodies (including cabs): safety seat belts, other
- 8708 22 10 00For the industrial assembly of: pedestrian-controlled tractors of subheading 8701 10; vehicles of heading 8703; vehicles of heading 8704 with either a compression-ignition internal combustion piston engine (diesel or semi-diesel) of a cylinder capacity not exceeding 2 500 cm3 or with a spark-ignition internal combustion piston engine of a cylinder capacity not exceeding 2 800 cm3; vehicles of heading 8705
- 8708 22 90 00Front windscreens: other
- 8708 29 10 11Specific pre-assembled or ready-to assemble sections for new mobile cranes
- 8708 29 10 99For the industrial assembly of: other
- 8708 29 90 11Specific pre-assembled or ready-to assemble sections for new mobile cranes
- 8708 29 90 99Other parts and accessories of bodies (including cabs): other, other, other
- 8708 30 10 40Body of disc type brake in bir (" ball in ramp") or epb (" electronic parking brake") or with hydraulic function only, containing functional and mounting openings and guide grooves, of a kind used in the manufacture of goods of chapter 87
- 8708 30 10 70Ductile cast iron brake caliper jaw, of a kind used in the manufacture of goods of chapter 87
- 8708 30 10 90For the industrial assembly of: other
- 8708 30 91 30Body of disc type brake in bir (" ball in ramp") or epb (" electronic parking brake") or with hydraulic function only, containing functional and mounting openings and guide grooves, of a kind used in the manufacture of goods of chapter 87
- 8708 30 91 40Ductile cast iron brake caliper jaw, of a kind used in the manufacture of goods of chapter 87
- 8708 30 91 90Brakes and servo-brakes; parts thereof: other, for disc brakes, other
- 8708 30 99 00Brakes and servo-brakes; parts thereof: other, other
- 8708 40 20 20Automatic hydrodynamic gearbox - with a hydraulic torque converter, - without transfer box and cardan shaft, - whether or not with front differential, for use in the manufacture of motor vehicles of chapter 87
- 8708 40 20 25Transmission assembly consisting of: -double pinion type planetary gear shifting mechanism, -sport sequential shiftmatic system with a speed of 7 or more but not more than 10, -a width of 280 mm or more but no more than 470 mm, -a height of 350 mm or more but no more than 595 mm, -a length of 410 mm or more but no more than 690 mm, -a weight of 70 kg or more but no more than 110 kg, for use in the manufacture of motor vehicles of subheading 8703 22 and 8703 23
- 8708 40 20 70Manual gearbox in cast aluminium housing for transverse installation with: - maximum dimensions of 550 x 500 x 600mm -five or six gears, -a differential gear, -an engine torque of 400 nm or less, for use in the manufacture of motor vehicles of heading 8703
- 8708 40 20 80Transmission gearbox without torque converter, with: - dual clutch, - 7 or more forward gears, - 1 reverse gear, - a maximum torque of 450nm, - whether or not with electric motor integrated, - a height of 350mm or more but not more than 600mm, - a width 350mm or more but not more than 600mm, and - a weight of 70kg or more but not more than 110kg, for use in the manufacture of motor vehicles of heading 8703
- 8708 40 20 90For the industrial assembly of: other
- 8708 40 50 10Automatic hydrodynamic gearbox - with a hydraulic torque converter, - without transfer box and cardan shaft, - whether or not with front differential, for use in the manufacture of motor vehicles of chapter 87
- 8708 40 50 25Transmission assembly housing 3 other shafts inside it and offering a rotating switch for shift position, consisting of: -cast aluminium body, -differential gear, -2 electrical motors and gears, -a width of 280 mm or more but no more than 470 mm, -a height of 350 mm or more but no more than 595 mm, -a length of 410 mm or more but no more than 690 mm, for use in the manufacture of motor vehicles of subheadings 8703 40 and 8703 60
- 8708 40 50 60Manual gearbox in cast aluminium housing for transverse installation with: - maximum dimensions of 550 x 500 x 600mm -five or six gears, -a differential gear, -an engine torque of 400 nm or less, for use in the manufacture of motor vehicles of heading 8703
- 8708 40 50 70Automatic transmission equipped with double clutch system with: -at least 8 gears, -an engine torque of 800 nm or more, -an electronic differential, -a p-lock safety system, and -a tcu transmission control unit, for use in the manufacture of motor vehicles of heading 8703
- 8708 40 50 90Gear boxes and parts thereof: other, gear boxes, other
- 8708 40 91 00Of closed-die forged steel
- 8708 40 99 00Gear boxes and parts thereof: other, parts, other
- 8708 50 20 15Spherical outboard constant velocity joint ball bearing cage, part of the vehicle's drive system, made of material suitable to be carburised with a carbon content of 0.14% or more but not more than 0.57%, forged, turned, punched, milled and hardened
- 8708 50 20 18Propeller shaft for torque transmission from the gearbox to the rear axle, consisting of: -two cardan rods, -central universal joint, -central bearing with suspension in a plastic cover, -universal joints on both ends of the shaft, -slip, tube and end yokes, -of a length of 1.4 m or more but not more than 2.4 m, for use in the production of goods of chapter 87
- 8708 50 20 20Transmission shaft in carbon fibre reinforced plastics consisting of a unique piece without any joint in the middle - of a length of 1 m or more but not more than 2 m, - of a weight of 6 kg or more but not more than 9 kg
- 8708 50 20 25Ball-type outboard constant velocity joint housing for transmitting a torque from the engine and transmission to the wheels of motor vehicles, in a form of an outer race, with: -6 ball tracks or more but not more than 8, with -a thread, -an external involute spline with 21 or more but not more than 38 teeth, -for running with bearing balls made of steel with a carbon content of 0.48% or more but not more than 0.57%, -forged, turned, milled and hardened
- 8708 50 20 35Inboard constant velocity joint tripod housing, with: -an outer diameter of 67.0 mm or more but not more than 99.0 mm, -3 cold calibrated roller tracks with a diameter of 29.95 mm or more but not more than 49.2 mm, -an external spline with 21 teeth or more but not more than 41, -forged, turned, rolled and hardened
- 8708 50 20 50Double flange bearing of 3rd generation, for motor vehicles, - with double-row ball bearing, - whether or not with impulse (encoder) ring, - whether or not with antilock brake system (abs) sensor, - whether or not with mounted screws, for use in the manufacture of goods of chapter 87
- 8708 50 20 55Inboard constant velocity joint tripod spider, part of the vehicle's drive system, with: -3 trunnions with a diameter of 17.128 mm or more but not more than 25.468 mm, -forged, turned, broached and hardened
- 8708 50 20 70Housing of tripod type half shaft inboard joint for transmitting a torque from engine and transmission to wheels of motor vehicles with: -an outer diameter of 67.0 mm or more but not more than 84.5 mm, -3 cold calibrated roller tracks with a diameter of 29.90 mm or more but not more than 36.60 mm, - sealing diameter 34.0 mm or more but not more than 41.0 mm, without lead angle, -spline with 21 teeth or more but not more than 35, -bearing seat diameter of 25.0 mm or more but not more than 30.0 mm, with or without oil grooves
- 8708 50 20 75Constant velocity joint assembly for transmitting a torque from engine and transmission to wheels of motor vehicles, consisting of: - an inner race with 6 ball tracks or more but not more than 8 for running with the bearing balls with a diameter of 13.0mm or more but not more than 28.0mm, - an outer race with 6 ball tracks or more but not more than 8 for running with the bearing balls, made of steel with carbon content of 0.45% or more but not more than 0.58%, with thread and with a spline with 22 teeth or more but not more than 44, - a spherical cage keeping bearing balls in the ball tracks of outer race and inner race in proper angular position, made of material suitable for carburising with carbon content of 0.14% or more but not more than 0.55%, and - with a grease compartment, - capable of working at constant speed at variable articulation angle not higher than 52 degrees
- 8708 50 20 80Specific pre-assembled or ready-to assemble sections for new mobile cranes
- 8708 50 20 90For the industrial assembly of: other
- 8708 50 35 11Specific pre-assembled or ready-to assemble sections for new mobile cranes
- 8708 50 35 90Drive-axles with differential, whether or not provided with: other
- 8708 50 55 11Specific pre-assembled or ready-to assemble sections for new mobile cranes
- 8708 50 55 20Double flange bearing of 3rd generation, for motor vehicles, - with double-row ball bearing, - whether or not with impulse (encoder) ring, - whether or not with antilock brake system (abs) sensor, - whether or not with mounted screws, for use in the manufacture of goods of chapter 87
- 8708 50 55 50Spherical outboard constant velocity joint ball bearing cage, part of the vehicle's drive system, made of material suitable to be carburised with a carbon content of 0.14% or more but not more than 0.57%, forged, turned, punched, milled and hardened
- 8708 50 55 91Specific pre-assembled or ready-to assemble sections for new mobile cranes
- 8708 50 55 99Of closed-die forged steel: other, other
- 8708 50 91 10Double flange bearing of 3rd generation, for motor vehicles, - with double-row ball bearing, - whether or not with impulse (encoder) ring, - whether or not with antilock brake system (abs) sensor, - whether or not with mounted screws, for use in the manufacture of goods of chapter 87
- 8708 50 91 11Specific pre-assembled or ready-to assemble sections for new mobile cranes
- 8708 50 91 90Drive-axles with differential, whether or not provided with: other, parts, other, for non-driving axles, other
- 8708 50 99 10Transmission shaft in carbon fibre reinforced plastics consisting of a unique piece without any joint in the middle - of a length of 1 m or more but not more than 2 m, - of a weight of 6 kg or more but not more than 9 kg
- 8708 50 99 25Housing of tripod type half shaft inboard joint for transmitting a torque from engine and transmission to wheels of motor vehicles with: -an outer diameter of 67.0 mm or more but not more than 84.5 mm, -3 cold calibrated roller tracks with a diameter of 29.90 mm or more but not more than 36.60 mm, - sealing diameter 34.0 mm or more but not more than 41.0 mm, without lead angle, -spline with 21 teeth or more but not more than 35, -bearing seat diameter of 25.0 mm or more but not more than 30.0 mm, with or without oil grooves
- 8708 50 99 35Constant velocity joint assembly for transmitting a torque from engine and transmission to wheels of motor vehicles, consisting of: - an inner race with 6 ball tracks or more but not more than 8 for running with the bearing balls with a diameter of 13.0mm or more but not more than 28.0mm, - an outer race with 6 ball tracks or more but not more than 8 for running with the bearing balls, made of steel with carbon content of 0.45% or more but not more than 0.58%, with thread and with a spline with 22 teeth or more but not more than 44, - a spherical cage keeping bearing balls in the ball tracks of outer race and inner race in proper angular position, made of material suitable for carburising with carbon content of 0.14% or more but not more than 0.55%, and - with a grease compartment, - capable of working at constant speed at variable articulation angle not higher than 52 degrees
- 8708 50 99 40Double flange bearing of 3rd generation, for motor vehicles, - with double-row ball bearing, - whether or not with impulse (encoder) ring, - whether or not with antilock brake system (abs) sensor, - whether or not with mounted screws, for use in the manufacture of goods of chapter 87
- 8708 50 99 45Ball-type outboard constant velocity joint housing for transmitting a torque from the engine and transmission to the wheels of motor vehicles, in a form of an outer race, with: -6 ball tracks or more but not more than 8, with -a thread, -an external involute spline with 21 or more but not more than 38 teeth, -for running with bearing balls made of steel with a carbon content of 0.48% or more but not more than 0.57%, -forged, turned, milled and hardened
- 8708 50 99 50Inboard constant velocity joint tripod housing, with: -an outer diameter of 67.0 mm or more but not more than 99.0 mm, -3 cold calibrated roller tracks with a diameter of 29.95 mm or more but not more than 49.2 mm, -an external spline with 21 teeth or more but not more than 41, -forged, turned, rolled and hardened
- 8708 50 99 60Inboard constant velocity joint tripod spider, part of the vehicle's drive system, with: -3 trunnions with a diameter of 17.128 mm or more but not more than 25.468 mm, -forged, turned, broached and hardened
- 8708 50 99 70Specific pre-assembled or ready-to assemble sections for new mobile cranes
- 8708 50 99 90Drive-axles with differential, whether or not provided with: other, parts, other, other, other
- 8708 70 10 15Fitted with pneumatic tyres, new or retreaded, of rubber, of a kind used for buses or lorries, with a load index exceeding 121
- 8708 70 10 50Wheels of aluminium, whether or not with their accessories: other
- 8708 70 10 80Fitted with pneumatic tyres, new or retreaded, of rubber, of a kind used for buses or lorries, with a load index exceeding 121
- 8708 70 10 85Road wheels of steel, whether or not with their accessories: other
- 8708 70 10 92Fitted with pneumatic tyres, new or retreaded, of rubber, of a kind used for buses or lorries, with a load index exceeding 121
- 8708 70 10 95For the industrial assembly of: other, other, other
- 8708 70 50 15Fitted with pneumatic tyres, new or retreaded, of rubber, of a kind used for buses or lorries, with a load index exceeding 121
- 8708 70 50 50Wheels of aluminium, whether or not with their accessories: other
- 8708 70 50 80Fitted with pneumatic tyres, new or retreaded, of rubber, of a kind used for buses or lorries, with a load index exceeding 121
- 8708 70 50 85Wheels of aluminium: other, other
- 8708 70 91 15Fitted with pneumatic tyres, new or retreaded, of rubber, of a kind used for buses or lorries, with a load index exceeding 121
- 8708 70 91 90Wheel centres in star form, cast in one piece, of iron: other
- 8708 70 99 20Road wheels of steel, whether or not with their accessories
- 8708 70 99 30Fitted with pneumatic tyres, new or retreaded, of rubber: other
- 8708 70 99 80Road wheels of steel, whether or not with their accessories and whether or not fitted with tyres, designed for - road tractors, - motor vehicles for the transport of persons and/or the transport of goods, - special purpose motor vehicles (for example, fire fighting vehicles, spraying lorries); excluding: - wheels for road quad bikes, - wheels for motor vehicles specifically designed for uses other than on public roads (for example, wheels for agricultural tractors or forestry tractors, for forklifts, for pushback tractors, for dumpers designed for off-highway use)
- 8708 70 99 85Road wheels and parts and accessories thereof: other, other, other, other
- 8708 80 20 10Upper strut insulator containing - a metal holder with three mounting screws, and - a rubber bump for use in the manufacture of goods of chapter 87
- 8708 80 20 90For the industrial assembly of: other
- 8708 80 35 10Upper strut insulator containing - a metal holder with three mounting screws, and - a rubber bump for use in the manufacture of goods of chapter 87
- 8708 80 35 90Suspension systems and parts thereof: other, suspension shock-absorbers, other
- 8708 80 55 00Anti roll bars; other torsion bars
- 8708 80 91 00Of closed-die forged steel
- 8708 80 99 30Surface-hardened, steel piston rod for a hydraulic or hydropneumatic shock absorber of motor vehicles: -with a chrome coating, -of a diameter of 11 mm or more, but not more than 28 mm, -of a length of 80 mm or more, but not more than 600 mm, with a threaded end or a mandrel for resistance welding
- 8708 80 99 90Suspension systems and parts thereof: other, other, other, other
- 8708 91 20 20Aluminium cooler using compressed air with a ribbed design of a kind used in the manufacture of goods of chapter 87
- 8708 91 20 30Aluminium alloy inlet or outlet air tank of heat exchangers for car cooling systems, manufactured to standard en ac 42100 or en ac 43000 t6 with - an insulating area flatness of not more than 0.1 mm, - a permissible particle quantity of 0.3 mg per tank, - a distance between pores of 2 mm or more, - pore sizes of not more than 0.4 mm, and - not more than 3 pores larger than 0.2mm -with a weight of 0.2kg or more but not more than 3kg
- 8708 91 20 90For the industrial assembly of: other
- 8708 91 35 10Aluminium cooler using compressed air with a ribbed design of a kind used in the manufacture of goods of chapter 87
- 8708 91 35 20Turbocharger cooling duct containing: -an aluminum alloy duct with at least one metal holder and at least two mounting holes, -a rubber pipe with clips, -a stainless steel flange highly resistant to corrosion [sus430jil], for use in the manufacture of compression ignition engines of motor vehicles
- 8708 91 35 30Two-circuit aluminum heat exchanger for automatic transmission of passenger cars: -of the stack-plate type, -with two pairs of inlet and outlet, each for the coolant/water circuit and the transmission oil circuit, -with at least two mounting holes, -whether or not with the connection hoses, for use in the manufacture of goods of chapter 87
- 8708 91 35 40Radiators: -with corrosion protection, -for pressures up to 150 psi (1034 kpa), -with individual replaceable, cooling tubes in brass or copper, for use in the production of engine and charge air cooling with a weight of 265 kg or more but not more than 599 kg
- 8708 91 35 90Radiators and parts thereof: other, radiators, other
- 8708 91 91 00Of closed-die forged steel
- 8708 91 99 30Aluminium alloy inlet or outlet air tank of heat exchangers for car cooling systems, manufactured to standard en ac 42100 or en ac 43000 t6 with - an insulating area flatness of not more than 0.1 mm, - a permissible particle quantity of 0.3 mg per tank, - a distance between pores of 2 mm or more, - pore sizes of not more than 0.4 mm, and - not more than 3 pores larger than 0.2mm -with a weight of 0.2kg or more but not more than 3kg
- 8708 91 99 90Radiators and parts thereof: other, parts, other, other
- 8708 92 20 00For the industrial assembly of: pedestrian-controlled tractors of subheading 8701 10; vehicles of heading 8703; vehicles of heading 8704 with either a compression-ignition internal combustion piston engine (diesel or semi-diesel) of a cylinder capacity not exceeding 2 500 cm3 or with a spark-ignition internal combustion piston engine of a cylinder capacity not exceeding 2 800 cm3; vehicles of heading 8705
- 8708 92 35 00Silencers (mufflers) and exhaust pipes
- 8708 92 91 00Of closed-die forged steel
- 8708 92 99 00Silencers (mufflers) and exhaust pipes; parts thereof: other, parts, other
- 8708 93 10 00For the industrial assembly of: pedestrian-controlled tractors of subheading 8701 10; vehicles of heading 8703; vehicles of heading 8704 with either a compression-ignition internal combustion piston engine (diesel or semi-diesel) of a cylinder capacity not exceeding 2 500 cm3 or with a spark-ignition internal combustion piston engine of a cylinder capacity not exceeding 2 800 cm3; vehicles of heading 8705
- 8708 93 90 00Clutches and parts thereof: other
- 8708 94 20 00For the industrial assembly of: vehicles of heading 8703; vehicles of heading 8704 with either a compression-ignition internal combustion piston engine (diesel or semi-diesel) of a cylinder capacity not exceeding 2 500 cm3 or with a spark-ignition internal combustion piston engine of a cylinder capacity not exceeding 2 800 cm3; vehicles of heading 8705
- 8708 94 35 00Steering wheels, steering columns and steering boxes
- 8708 94 91 00Of closed-die forged steel
- 8708 94 99 10Hub gear made of cold rolled carbon steel (per astm a1008), molded into the plastic and pressed on pinion, with: -an outer diameter of 81.2 mm or more, but not more than 82.55 mm, -an inner diameter of 25.9 mm or more, but not more than 25.97 mm, -a height of the lower side of inner diameter of 11.63 mm or more, but not more than 12.13 mm, -a height of the upper side of inner diameter of 3.25 mm or more, but not more than 3.5 mm, -an overall height of 11.63 mm or more, but not more than 19.5 mm for use in the manufacture of vehicle's steering system
- 8708 94 99 20Intermediate steering shaft forming part of the steering column with: -a torsional rigidity of 25 nm/degree or more, -a tubular male shaft in welded carbon steel tube (per gb/t 699 grade 20), -a tubular female shaft in welded carbon steel tube (per with gb/t 699 grade 20), -two spiders universal joint made of chromium alloy steel (per gb/t 5216 grade 20crmntih), -a length in nominal telescope position of 396 mm or more but not more than 467 mm, -a coupling interface on both ends with internal toothing, -two cardan joints on both sides, -a telescope shaft function with a range of 74 mm or more but not more than 115 mm, for use in the manufacture of vehicle's steering system
- 8708 94 99 30Lower assist shaft as part of the steering column made of carbon steel (per gb/t699 grade 45 or jis g4051 grade s45c) with: -an ultimate torsional strength load of 325 nm or more and johnson apparent elastic limit (j.a.e.l) values of 275 nm or more, -a length of 66.39 mm or more but not more than 88.64 mm, -an outer diameter of 27.47 mm or more but not more than 28.38 mm, -an inner hole of diameter 6.50 mm or more but not more than 6.58 mm, -an external 26-teeth spline with major diameter 21.18 mm or more but not more than 21.44 mm, -a knurling on a part of outer surface of major diameter 26.0 mm or more but not more than 26.1 mm, -with or without an external 24-tooth spline and with a major diameter 24.75 mm or more but not more than 25 mm, for use in the manufacture of vehicle's steering system
- 8708 94 99 40Upper assist shaft as part of the steering column made of carbon steel (per gb/t699 grade 45) with: -an ultimate torsional strength load of 325 nm or more and johnson apparent elastic limit (j.a.e.l) values of 275 nm or more, -a length of 165.3 mm or more but not more than 204.2 mm, -an outer diameter of 22.87 mm or more but not more than 22.92 mm, -an internal hole of diameter 6.50 or more but not more than 6.58 mm, -an external spline, for use in the manufacture of vehicle's steering system
- 8708 94 99 50Lower shaft as part of the steering column made of aluminium alloy (per astm b221m grade 6105), air quenched and tempered with: -an ultimate torsional strength of 260 nm or more, -a length of 296.7 mm or more but not more than 297.8 mm, -an external 18-tooth spline on all shaft length with major diameter of 28.7 mm or more but not more than 29 mm, -an 18-tooth internal spline with a minor diameter of 19.7 mm or more but not more than 20 mm, for use in the manufacture of vehicle's steering system
- 8708 94 99 60Torsion bar as part of the steering column made of carbon alloy steel (per sae j1268, grade 5160h of modified chemistry for carbon content of 0.53 or more, but not more than 0.56) with: -a shaft torsional stiffness of 2.5 nm/degree or more but not more than 2.7 nm/degree, -a length of 107.75 mm or more but not more than 108.25 mm, -an outer diameter of 6.38 mm or more but not more than 6.42 mm, -two external 18-tooth splines on both shaft ends with a major diameter of 6.70 mm or more but not more than 6.85 mm, as interface to pressing with matting input and output shafts, -entire surface shot peened, for use in the manufacture of vehicle's steering system
- 8708 94 99 70Tubular steering shaft as part of the steering column made of carbon steel welded tube (per en 10305/2, e235 c or gb/t699 grade 20) with: -an ultimate torsional strength of 300 nm or more and johnson apparent elastic limit (j.a.e.l) values of 275 nm or more, -a length of 245.48 mm or more but not more than 287.5 mm, -an outer diameter of 23.95 mm or more but not more than 32.25 mm, -an interface for steering wheel connection either in a form of an external 40-tooth spline with major diameter of 17.1 mm or more but not more than 17.5 mm and an internal thread m12x1.75-6h or in a form of an external hexagon with a short diagonal of 15.05 mm or more but not more than 15.35mm and an internal thread m10x1.5-6h, -an interface either in a form of an internal 10-tooth spline of length of 98.0 mm or more but not more than 160 mm, with minor diameter of 16.1 mm or more but not more than 16.4 mm or in a form of an internal 48-tooth spline of length of 151 mm or more but not more than 160 mm, with minor diameter of 23.2 mm or more but not more than 23.3 mm, for use in the manufacture of vehicle's steering system
- 8708 94 99 80Blank assembly worm gear, consisting of a hub of carbon steel (gb/t 699 grade 25 or din en 10277 grade 11smn30) and a ring of cast polyamide 6/12 with: - an outer diameter of 97.35 mm or more, but not more than 102.65 mm, - an inner diameter of 27.91 mm or more, but not more than 27.93 mm, - a height of the hub of 11.75 mm or more, but not more than 12.00 mm, - an overall height of 16.00 mm or more, but not more than 18.00 mm
- 8708 94 99 90Steering wheels, steering columns and steering boxes: other, parts, other, other
- 8708 95 10 20Inflatable safety cushion of high strength polyamide fibre: - sewn, - folded, - with three-dimensionally applied silicone bonding for air bag cavity forming and load-regulated air bag sealing - suitable for cool inflator technology
- 8708 95 10 30Inflatable sewn safety cushion of high strength polyamide fibre: -folded into three-dimensional packing form, fixed by thermal forming, dedicated fixation seams, fabric cover or plastic staples, or -flat safety cushion with or without thermal folding
- 8708 95 10 90For the industrial assembly of: other
- 8708 95 91 00Of closed-die forged steel
- 8708 95 99 30Inflatable safety cushion of high strength polyamide fibre: - sewn, - folded, - with three-dimensionally applied silicone bonding for air bag cavity forming and load-regulated air bag sealing - suitable for cool inflator technology
- 8708 95 99 40Inflatable sewn safety cushion of high strength polyamide fibre: -folded into three-dimensional packing form, fixed by thermal forming, dedicated fixation seams, fabric cover or plastic staples, or -flat safety cushion with or without thermal folding
- 8708 95 99 50Airbag inflator containing pyrotechnics, whether or not cold gas, as propellant for safety airbags of vehicles, in each individual consignment of 1 000 pieces or more
- 8708 95 99 90Safety airbags with inflator system; parts thereof: other, other, other
- 8708 99 10 55Silicone or plastic keyboards, comprising: -parts of common metal, and -whether or not comprising parts of plastic, -epoxy resin reinforced with fiberglass or wood, -whether or not printed or surface-treated, -with or without electrical conductors, -with or without a membrane bonded to the keyboard, -with or without mono or multilayer protective film
- 8708 99 10 60Aluminium engine bracket, with dimensions of: -height of more than 10 mm but not more than 200 mm, -width of more than 10 mm but not more than 250 mm, -length of more than 10 mm but not more than 200 mm, equipped with at least two fixing holes, made of aluminium alloys enac-46100 or enac-42100 (based on the norm en:1706) with following characteristics: -internal porosity not more than 1 mm, -outer porosity not more than 2 mm, -rockwell hardness hrb 10 or more, of a kind used in the production of suspensions systems for engines in motor vehicles
- 8708 99 10 80Specific pre-assembled or ready-to assemble sections for new mobile cranes
- 8708 99 10 90For the industrial assembly of: other
- 8708 99 93 11Specific pre-assembled or ready-to assemble sections for new mobile cranes
- 8708 99 93 90Of closed-die forged steel: other
- 8708 99 97 22Silicone or plastic keyboards, comprising: -parts of common metal, and -whether or not comprising parts of plastic, -epoxy resin reinforced with fiberglass or wood, -whether or not printed or surface-treated, -with or without electrical conductors, -with or without a membrane bonded to the keyboard, -with or without mono or multilayer protective film
- 8708 99 97 27Inner pole electromagnet core used in magneto-rheological engine mounts to reduce shocks and for isolation and damping in passenger cars: -of a powder metal assembly, -with a diameter of not more than 90.95 mm, -with an overall height of 24.5 mm, -impregnated with sealant, -zinc plated
- 8708 99 97 43Outer tie rod with a housing made of aisi 4137 (scm435) steel or en10083/2- c45r n steel or jis g4053-scm435 low alloy steel, with: -a ball stud made of en 10263/4 - 41crs4 q t steel or aisi 4137 (scm435) steel or en10083/3-42crmos4q t steel or jis g4053-scm435 low alloy steel, -a polyoxymethylene plastic ball seat, -a distance between the end of the threaded hole and the centre of the ball stud of 124 mm or more but not more than 194 mm, -a ball stud diameter of 21.98 mm or more but no more than 22 mm, -a threaded hole depth of 40.5 mm or more but no more than 52 mm with dimensions m14x1.5, -a boot seal, -a boot seal protector and retaining ring, -lubricant, for use in the manufacture of vehicle's steering system
- 8708 99 97 50Aluminium engine bracket, with dimensions of: -height of more than 10 mm but not more than 200 mm, -width of more than 10 mm but not more than 250 mm, -length of more than 10 mm but not more than 200 mm, equipped with at least two fixing holes, made of aluminium alloys enac-46100 or enac-42100 (based on the norm en:1706) with following characteristics: -internal porosity not more than 1 mm, -outer porosity not more than 2 mm, -rockwell hardness hrb 10 or more, of a kind used in the production of suspensions systems for engines in motor vehicles
- 8708 99 97 53Roll rod assembly for the front suspension in vehicles for connecting the stabilizer to the suspension components: -made of aluminum, rubber, and plastic, -with a height of 270 mm or more, but not more than 300 mm, -with a width of 50 mm or more, but not more than 65 mm, -with a length of 150 mm or more, but not more than 170 mm, for use in the manufacture of motor vehicles
- 8708 99 97 58Mounting bracket of front radiator or intercooler: -made of iron or steel or of plastics, -whether or not with rubber cushioning, for use in the manufacture of goods of heading 8708
- 8708 99 97 75Aluminium alloy support bracket, with mounting holes, whether or not with fixation nuts, for indirect connection of the gearbox to the car body for use in the manufacture of goods of chapter 87
- 8708 99 97 80Specific pre-assembled or ready-to assemble sections for new mobile cranes
- 8708 99 97 90Other parts and accessories: other, other, other, other
8709 Works trucks, self-propelled, not fitted with lifting or handling equipment, of the type used in factories, warehouses, dock areas or airports for short distance transport of goods; tractors of the type used on railway station platforms; parts of the foregoing vehicles
- 8709 11 10 00Specially designed for the transport of highly radioactive materials
- 8709 11 90 00Works trucks, self-propelled, not fitted with lifting: vehicles, electrical, other
- 8709 19 10 00Specially designed for the transport of highly radioactive materials
- 8709 19 90 00Works trucks, self-propelled, not fitted with lifting: vehicles, other, other
- 8709 90 00 00Works trucks, self-propelled, not fitted with lifting: parts
8710 Tanks and other armoured fighting vehicles, motorised, whether or not fitted with weapons, and parts of such vehicles
8711 Motorcycles (including mopeds) and cycles fitted with an auxiliary motor, with or without side-cars; side-cars
- 8711 10 00 00With internal combustion piston engine of a cylinder capacity not exceeding 50 cm3
- 8711 20 10 00With internal combustion piston engine of a cylinder: scooters
- 8711 20 92 00Exceeding 50 cm3 but not exceeding 125 cm3
- 8711 20 98 00Exceeding 125 cm3 but not exceeding 250 cm3
- 8711 30 10 00Of a cylinder capacity exceeding 250 cm3 but not exceeding 380 cm3
- 8711 30 90 00Of a cylinder capacity exceeding 380 cm3 but not exceeding 500 cm3
- 8711 40 00 00With internal combustion piston engine of a cylinder capacity exceeding 500 cm3 but not exceeding 800 cm3
- 8711 50 00 00With internal combustion piston engine of a cylinder capacity exceeding 800 cm3
- 8711 60 10 00Bicycles, tricycles and quadricycles, with pedal assistance, with an auxiliary electric motor with a continuous rated power not exceeding 250 watts
- 8711 60 90 10Cycles, with pedal assistance, with an auxiliary electric motor
- 8711 60 90 90With electric motor for propulsion: other, other
- 8711 90 00 00Motorcycles: other
8712 Bicycles and other cycles (including delivery tricycles), not motorised
- 8712 00 30 10Bicycles with ball bearings: consigned from Indonesia, Malaysia, Sri Lanka or Tunisia
- 8712 00 30 20Bicycles with ball bearings: consigned from Cambodia, Pakistan or the Philippines
- 8712 00 30 90Bicycles with ball bearings: other
- 8712 00 70 10Bicycles and other cycles: other, unicycles
- 8712 00 70 91Bicycles and other cycles: other, other, consigned from Indonesia, Malaysia, Sri Lanka or Tunisia
- 8712 00 70 92Bicycles and other cycles: other, other, consigned from Cambodia, Pakistan or the Philippines
- 8712 00 70 99Bicycles and other cycles: other, other, other
8713 Carriages for disabled persons, whether or not motorised or otherwise mechanically propelled
8714 Parts and accessories of vehicles of headings 8711 to 8713
- 8714 10 10 00Brakes and parts thereof
- 8714 10 20 00Gear boxes and parts thereof
- 8714 10 30 00Road wheels and parts and accessories thereof
- 8714 10 40 00Silencers (mufflers) and exhaust pipes; parts thereof
- 8714 10 50 00Clutches and parts thereof
- 8714 10 90 70Motor bikes radiators in consignment of 100 pieces or more
- 8714 10 90 90Of motorcycles (including mopeds): other, other
- 8714 20 00 00Of carriages for disabled persons
- 8714 91 10 21Constructed from carbon fibres and artificial resin, for use in the manufacture of bicycles (including e-bikes)
- 8714 91 10 25Frame, constructed from aluminium or aluminium and carbon fibres and artificial resin, for the use in the manufacture of bicycles (including electric bicycles)
- 8714 91 10 29Painted, anodised, polished and/or lacquered: originating in or consigned from China: - in quantities below 300 units per month on average for a period not exceeding 12 months, or to be transferred to a party in quantities below 300 units per month on average for a period not exceeding 12 months; or - to be transferred to another holder of an end-use authorisation or to exempted parties, other
- 8714 91 10 31Constructed from carbon fibres and artificial resin, for use in the manufacture of bicycles (including e-bikes)
- 8714 91 10 35Frame, constructed from aluminium or aluminium and carbon fibres and artificial resin, for the use in the manufacture of bicycles (including electric bicycles)
- 8714 91 10 39Painted, anodised, polished and/or lacquered: other, other
- 8714 91 10 75Constructed from carbon fibres and artificial resin, for use in the manufacture of bicycles (including e-bikes)
- 8714 91 10 77Frame, constructed from aluminium or aluminium and carbon fibres and artificial resin, for the use in the manufacture of bicycles (including electric bicycles)
- 8714 91 10 89Frames and forks, and parts thereof: frames, other, other
- 8714 91 30 25Front forks, except rigid (non-telescopic) front forks made entirely of steel, for use in the manufacture of bicycles (including electric bicycles)
- 8714 91 30 29Painted, anodised, polished and/or lacquered: originating in or consigned from China: - in quantities below 300 units per month on average for a period not exceeding 12 months, or to be transferred to a party in quantities below 300 units per month on average for a period not exceeding 12 months; or - to be transferred to another holder of an end-use authorisation or to exempted parties, other
- 8714 91 30 35Front forks, except rigid (non-telescopic) front forks made entirely of steel, for use in the manufacture of bicycles (including electric bicycles)
- 8714 91 30 39Painted, anodised, polished and/or lacquered: other, other
- 8714 91 30 72Front forks, except rigid (non-telescopic) front forks made entirely of steel, for use in the manufacture of bicycles (including electric bicycles)
- 8714 91 30 89Frames and forks, and parts thereof: front forks, other, other
- 8714 91 90 00Frames and forks, and parts thereof: parts
- 8714 92 10 00Wheel rims and spokes: rims
- 8714 92 90 00Wheel rims and spokes: spokes
- 8714 93 00 11Hubs, other than coaster braking hubs and hub brakes: free-wheel sprocket-wheels, originating in or consigned from China: - in quantities below 300 units per month on average for a period not exceeding 12 months, or to be transferred to a party in quantities below 300 units per month on average for a period not exceeding 12 months; or - to be transferred to another holder of an end-use authorisation or to exempted parties
- 8714 93 00 19Hubs, other than coaster braking hubs and hub brakes: free-wheel sprocket-wheels, other
- 8714 93 00 20Gear set to connect sprockets: -for mounting on a hub drum, -with 7 sprockets or more but not more than 12 sprockets, -with 10 or more but not more than 52 teeth for each sprocket, -with a weight of 200 g or more but not more than 800 g, -sprockets made of nickel-plated steel or aluminium, -with connectors (spacers) between the sprockets made of plastic or aluminium, -without a pawl mechanism, for use in the manufacture of bicycles and e-bikes
- 8714 93 00 90Hubs, other than coaster braking hubs and hub brakes: other
- 8714 94 20 05Coaster braking hubs and hub brakes
- 8714 94 20 91Brakes, including coaster braking hubs and hub brakes: brakes, other brakes, originating in or consigned from China: - in quantities below 300 units per month on average for a period not exceeding 12 months, or to be transferred to a party in quantities below 300 units per month on average for a period not exceeding 12 months; or - to be transferred to another holder of an end-use authorisation or to exempted parties
- 8714 94 20 99Brakes, including coaster braking hubs and hub brakes: brakes, other brakes, other
- 8714 94 90 11Brakes, including coaster braking hubs and hub brakes: parts, brake levers, originating in or consigned from China: - in quantities below 300 units per month on average for a period not exceeding 12 months, or to be transferred to a party in quantities below 300 units per month on average for a period not exceeding 12 months; or - to be transferred to another holder of an end-use authorisation or to exempted parties
- 8714 94 90 19Brakes, including coaster braking hubs and hub brakes: parts, brake levers, other
- 8714 94 90 90Brakes, including coaster braking hubs and hub brakes: parts, other
- 8714 95 00 00Parts and accessories of vehicles of headings 8711 to 8713: other, saddles
- 8714 96 10 10Pedals, for use in the manufacture of bicycles (including electric bicycles)
- 8714 96 10 90Pedals and crank-gear, and parts thereof: pedals, other
- 8714 96 30 10Pedals and crank-gear, and parts thereof: crank-gear, originating in or consigned from China: - in quantities below 300 units per month on average for a period not exceeding 12 months, or to be transferred to a party in quantities below 300 units per month on average for a period not exceeding 12 months; or - to be transferred to another holder of an end-use authorisation or to exempted parties
- 8714 96 30 90Pedals and crank-gear, and parts thereof: crank-gear, other
- 8714 96 90 00Pedals and crank-gear, and parts thereof: parts
- 8714 99 10 20Bicycle handlebars, - with or without integrated stem, - either made out of carbon fibres and synthetic resin or made of aluminium, for use in the manufacture of bicycles (including electric bicycles)
- 8714 99 10 29Parts and accessories of vehicles of headings 8711 to 8713: other, other, handlebars, originating in or consigned from China: - in quantities below 300 units per month on average for a period not exceeding 12 months, or to be transferred to a party in quantities below 300 units per month on average for a period not exceeding 12 months; or - to be transferred to another holder of an end-use authorisation or to exempted parties, other
- 8714 99 10 89Bicycle handlebars, - with or without integrated stem, - either made out of carbon fibres and synthetic resin or made of aluminium, for use in the manufacture of bicycles (including electric bicycles)
- 8714 99 10 99Parts and accessories of vehicles of headings 8711 to 8713: other, other, handlebars, other, other
- 8714 99 30 00Parts and accessories of vehicles of headings 8711 to 8713: other, other, luggage carriers
- 8714 99 50 11Derailleur gears, consisting of: -rear derailleur and mounting articles, -with or without front derailleur, for use in the manufacture of bicycles (including electric bicycles)
- 8714 99 50 19Parts and accessories of vehicles of headings 8711 to 8713: other, other, derailleur gears, originating in or consigned from China: - in quantities below 300 units per month on average for a period not exceeding 12 months, or to be transferred to a party in quantities below 300 units per month on average for a period not exceeding 12 months; or - to be transferred to another holder of an end-use authorisation or to exempted parties, other
- 8714 99 50 91Derailleur gears, consisting of: -rear derailleur and mounting articles, -with or without front derailleur, for use in the manufacture of bicycles (including electric bicycles)
- 8714 99 50 99Parts and accessories of vehicles of headings 8711 to 8713: other, other, derailleur gears, other, other
- 8714 99 90 11Complete wheels with or without tubes, tyres and sprockets: originating in or consigned from China: - in quantities below 300 units per month on average for a period not exceeding 12 months, or to be transferred to a party in quantities below 300 units per month on average for a period not exceeding 12 months; or - to be transferred to another holder of an end-use authorisation or to exempted parties
- 8714 99 90 19Complete wheels with or without tubes, tyres and sprockets: other
- 8714 99 90 30Seat posts, for use in the manufacture of bicycles (including electric bicycles)
- 8714 99 90 40Stem for bicycle handlebars, for use in the manufacture of bicycles (including electric bicycles)
- 8714 99 90 50Rear air shock absorber in form of a pneumatic spring element with oil damper for use in the manufacture of bicycles, including electrical bicycles
- 8714 99 90 89Parts and accessories of vehicles of headings 8711 to 8713: other, other, other; parts, other
8715 Baby carriages and parts thereof
8716 Trailers and semi-trailers; other vehicles, not mechanically propelled; parts thereof
- 8716 10 92 00Of a weight not exceeding 1 600 kg
- 8716 10 98 00Of a weight exceeding 1 600 kg
- 8716 20 00 00Self-loading or self-unloading trailers and semi-trailers for agricultural purposes
- 8716 31 00 00Tanker trailers and tanker semi-trailers
- 8716 39 10 00Specially designed for the transport of highly radioactive materials
- 8716 39 30 00Other trailers and semi-trailers for the transport of goods: other, other, new, semi-trailers
- 8716 39 50 00Other trailers and semi-trailers for the transport of goods: other, other, new, other
- 8716 39 80 00Other trailers and semi-trailers for the transport of goods: other, other, used
- 8716 40 00 00Other trailers and semi-trailers
- 8716 80 00 00Trailers and semi-trailers: other vehicles
- 8716 90 10 00Trailers and semi-trailers: parts, chassis
- 8716 90 30 00Trailers and semi-trailers: parts, bodies
- 8716 90 50 00Trailers and semi-trailers: parts, axles
- 8716 90 90 15Fitted with pneumatic tyres, new or retreaded, of rubber, of a kind used for buses or lorries, with a load index exceeding 121
- 8716 90 90 50Aluminium road wheels of vehicles of cn heading 8716: other
- 8716 90 90 95Road wheels of steel, whether or not with their accessories
- 8716 90 90 96Fitted with pneumatic tyres, new or retreaded, of rubber: other
- 8716 90 90 97Road wheels of steel, designed for trailers or semi-trailers, not mechanically propelled, of road tractors, whether or not with their accessories and whether or not fitted with tyres
- 8716 90 90 98Trailers and semi-trailers: parts, other parts, other, other, other